Jeep 2008 Cherokee Скачать руководство пользователя страница 328 | Manualshive

Страница: 328 / 490

Jeep 2008 Cherokee Скачать руководство пользователя страница 328

Telltale Light” will turn OFF only after the tires have been
inflated to the vehicle’s recommended cold tire pressure
value.

CAUTION!

The TPMS has been optimized for the original
equipment tires and wheels. TPMS pressures have
been established for the tire size equipped on your
vehicle. Undesirable system operation or sensor
damage may result when using replacement equip-
ment that is not of the same size, type, and/or style.
Aftermarket wheels can cause sensor damage. Do not
use aftermarket tire sealants or balance beads if your
vehicle is equipped with a TPMS, as damage to the
sensors may result.

CAUTION!

After inspecting or adjusting the tire pressure always
reinstall the valve stem cap. This will prevent mois-
ture and dirt from entering the valve stem, which
could damage the Tire Pressure Monitoring Sensor.

NOTE:

•

The TPMS is not intended to replace normal tire care
and maintenance, or to provide warning of a tire
failure or condition.

•

The TPMS should not be used as a tire pressure gauge
while adjusting your tire pressure.

•

Driving on a significantly under-inflated tire causes
the tire to overheat and can lead to tire failure.
Under-inflation also reduces fuel efficiency and tire
tread life, and may affect the vehicle’s handling and
stopping ability.

328

STARTING AND OPERATING

«
...
326
327
328
329
330
...
»

Содержание 2008 Cherokee











































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды