manualshive.com logo in svg

Jeep 2008 Cherokee, Руководство пользователя

Поделиться
Скачать
Jeep 2008 Cherokee Скачать руководство пользователя страница 297

4 LOW to 4 HI
With the vehicle at speeds of 0 to 3 mph (0 to 5 km/h),
key ON or engine running, shift the transmission into N
(Neutral), and raise the transfer case T-handle. The “4WD
LOW Indicator Lamp” in the instrument cluster will flash
and go out when the shift is complete. Release the
T-handle.

NOTE:

If shift conditions/interlocks are not met, or a

transfer case motor temperature protection condition
exists, a “CHECK SHIFT PROCEDURES” message will
flash from the EVIC (Electronic Vehicle Information Cen-
ter). Refer to “Electronic Vehicle Information Center
(EVIC)” in Section 4 of this manual.

NOTE:

Shifting into or out of 4WD LOW is possible

with the vehicle completely stopped, however difficulty
may occur due to the mating clutch teeth not being
properly aligned. Several attempts may be required for
clutch teeth alignment and shift completion to occur. The
preferred method is with the vehicle rolling 0 to 3 mph (0
to 5 km/h). If the vehicle is moving faster than 3 mph (5
km/h), the transfer case will not allow the shift.

Neutral (N) Shift Procedure

1. Key ON, engine off.

2. Vehicle stopped, with foot on brake.

3. Place transmission in N (Neutral).

STARTING AND OPERATING

297

5

Содержание 2008 Cherokee











































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды