Jeep 2008 Cherokee Скачать руководство пользователя страница 342 | Manualshive

Страница: 342 / 490

Jeep 2008 Cherokee Скачать руководство пользователя страница 342

WARNING!

Ethanol vapors are extremely flammable and could
cause serious personal injury. Never have any smok-
ing materials lit in or near the vehicle when remov-
ing the fuel filler tube cap (gas cap) or filling the
tank. Do not use E-85 as a cleaning agent and never
use it near an open flame.

Fuel Requirements

Your vehicle will operate on both unleaded gasoline with
an octane rating of 87, or E-85 fuel, or any mixture of
these two.

For best results, a refueling pattern that alternates be-
tween E-85 and unleaded gasoline should be avoided.
When you do switch fuels, it is recommended that

•

you do not switch when the fuel gauge indicates less
than 1/4 full

•

you do not add less than 5 gallons when refueling

•

you operate the vehicle immediately after refueling for
a period of at least 5 minutes

Observing these precautions will avoid possible hard
starting and/or significant deterioration in drivability
during warm up.

NOTE:

When the ambient temperature is above 90°F

(32°C), you may experience hard starting and rough idle
following start up even if the above recommendations are
followed.

342

STARTING AND OPERATING

«
...
340
341
342
343
344
...
»

Содержание 2008 Cherokee











































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды