background image

Part No. 960-000192R_Rev. A

© 2017 JCM American Corporation

5

August, 2017

JCM® Training Overview

GEN2U™ Printer

CLEANING PROCEDURES

Regular cleaning of the GEN2U Printer Unit will help promote optimum 
printer performance. Indications that the Printer may require cleaning include:

• Frequent paper jams
• Partial print output
• Light print quality 

The 

JCM Printer Cleaning Kit (P/N 350-00292-100)

 is recommended for best 

results cleaning the GEN2U Printer. The Cleaning Kit includes Alcohol Wipes, 
Cleaning Swabs, and feed-through Cleaning Cards. 

  

To clean the GEN2U Printer, use the following procedure:

1. Press the Lid Latch (refer to Figure 2 

on page 4) to open the Printer Lid.

2. Use a cleaning swab dampened with Isopropyl Alcohol to wipe clean the following 

Sensors (refer to Figure 4 on the following page):

• Printer Tray Sensor (Figure 4

 

a

)

• Paper Low Sensor (Figure 4

 

b

)

• Lid Open Sensor (Figure 4

 

d

)

• Ticket Taken Sensor (Figure 4

 

e

Table 2 

GEN2U Printer Sensor Cleaning Methods

Symbol

Sensor Type

Cleaning Method

a

Printer Tray (Drawer Open)

Wipe clean with an alcohol swab.

b

Ticket Low (Paper Low)

Wipe clean with an alcohol swab.

c

Paper Out (Index Mark)

Blow clean with compressed air.

d

Lid Open

Wipe clean with an alcohol swab.

e

Ticket Taken Sensor

Wipe clean with an alcohol swab.

NOTE: JCM strongly recommends a thorough cleaning of the GEN2U Printer at least 
once per year. Additional cleanings may be indicated, depending on environmental 
conditions where the GEN2U Printer is installed (e.g., smoke-filled or dusty 
environments).

 Figure 3 

JCM Printer Cleaning Kit (P/N 350-00292-100)

NOTE: GEN2U Printer Sensor Cleaning Methods are listed in Table 2 below. Refer to 
Figure 4 o
n the following page for Sensor locations.

Содержание GEN2U





















Отзывы: