JCM GAMMA VERSUS Series Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 111

background image

GAMMA VERSUS MANUAL

56

COD. 1257066 Gamma VERSUS Manual v1.13

7.20 Anti-intrusive function

Notes

In VERSUS control panels, flash function can be assigned to any type of output: free
voltage output, voltage output, TL-CARD-V output and front light output.

Model

All

Associated
parameters

ID

Description

Type

P78…P90 OUT

XX

OUTPUT

PA1…PB0

(TL-CARD-V) OUT XXX

OUTPUT

Description

The anti-intrusive function allows detecting a non-desired entrance to the garage (thief,
etc.). This function uses the closing security contact as a sensor to detect this non-
desired entrance.

Configuration

To enable the anti-intrusive function it is needed to configure any of the available
outputs as “Intrusive” by means a VERSUS-PROG programming tool. The

P78

to

P90

configuration parameters are used to configure the control panel outputs and the

PA1

to

PB0

configuration parameter are used to configure the TL-CARD-V extra outputs.

The configured “Intrusive” outputs will be activated in case of non-desired entrance
detection. Therefore these outputs can be used to activate any kind of alarm system.
The output is “normally opened” and it changes to “normally closed” when it is
activated. It keeps active until the door is completely closed.

To use the anti-intrusive function, a closing security contact input is compulsory as the
closing security contact is used as presence sensor. Therefore it is needed to configure
any of the available inputs as closing security contact input.

Operating

If any output is configured as “Intrusive” the control panel checks the closing security
contact activations.

If an opening maneuver starts in order to open the garage door, the control panel
checks the number of closing security contact activations.

The first activation is understood as the user enters to its garage but the second
activation means a non-desired entrance. If this second activation is detected before
the door returns to the CLOSED status “Intrusive” outputs are activated in order to
inform about a non-desired entrance.

«
...
54
55
56
57
58
...
»

Содержание GAMMA VERSUS Series
















































































































Отзывы:

Нет отзывов

Похожие инструкции для GAMMA VERSUS Series

Бренд: Warren Controls Страницы: 16

Бренд: IBM Страницы: 12

Бренд: K&K Страницы: 10

Бренд: OMC Страницы: 18

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 2

FrameSaver 9120

Бренд: Paradyne Страницы: 20

VeriSafe VS2-NET

Бренд: Panduit Страницы: 6

Бренд: vacuubrand Страницы: 12

Бренд: Vacon Страницы: 47

Бренд: Vacon Страницы: 40

Бренд: Waterway Страницы: 8

Бренд: Wenglor Страницы: 44

Бренд: DSC Страницы: 16

Бренд: Quickie Страницы: 108

Бренд: GARDINER TECHNOLOGY Страницы: 28

Бренд: Sames Страницы: 84

UNDER CONTROL CP-28

Бренд: G-Force Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды