background image

TRIUMPH-2 START GUIDE

14

UHF modem configuration

Open UHF Radio tab and set parameters:
• Output power for base: a value in dBm 

with 1 dB step in UHF Modem Output Pow-

er field.
Output power settings depend on the UHF 

transmitter model and could be selected 

from the following ranges:

• HPT401BT from 15 to 30 dBm (from 32 to 1000 mW)
• HPT404BT from 15 to 36 dBm (from 32 to 4000 mW)
• HPT435BT from 25 to 45.44 dBm (from 320 to 35000 

mW)

The correspondence between dBm and 

mW for the most frequently used power 

values is represented in the Table 1:

mW

30

100

250

500

1000

2000

4000

dBm

15

20

24

27

30

33

36

mW

10000

15000

20000

25000

32000

35000

dBm

40

42

43

44

45

46

• Operation frequency in UHF Modem Fre-

quency field in Hz (the frequency should 

be a multiply of 6500Hz)
• Protocol Type “simtx” for base. 
• Call sign in UHF Call Sign field.
Switch to Simplex protocol tab and set 

protocol parameters (Figure 16):

• Modulation type: dqpsk

• Channel spacing: 12500

• Scrambling: 255

• Forward Error Corrections: on

Click Apply to save the settings.
Frequency, output power, channel band-

Figure 16. NetView&Mo-

dem. Modems tab

Содержание TRIUMPH-2



















Отзывы: