Janus Pantheon Скачать руководство пользователя | Manualshive

Страница: 21 / 24

background image

INSTALLATION INSTRUCTIONS

This feature allows for the logic
controller to adjust for small operational
imbalances and permit the door to
operate as required in both directions
in conjunction with the electronic
sensitivity setting

Adjustments

shall be made

once the

electronic sensitivity setting has been
confirmed — refer to instructions under
the heading —”Setting the sensitivity
adjustment” . (previous page) step 8

Fine tuning is performed by

careful

rotation of the corresponding – open or
close setting - as required.

To

increase

+

the sensitivity of the

operator - rotate the required (open or
close) setting

ANTICLOCKWISE

To

decrease

-

the sensitivity of the

operator – rotate the required (open or
close) setting

CLOCKWISE

STEP 9

.

“Adusting the sensitivity”

«
...
19
20
21
22
23
...
»

Содержание Pantheon

























Отзывы:

Нет отзывов

Похожие инструкции для Pantheon

Бренд: GTO Страницы: 45

Security+ PD300D

Бренд: Chamberlain Страницы: 40

Бренд: Novoferm Страницы: 32

Бренд: Motorline professional Страницы: 14

Бренд: Micanan Страницы: 44

Бренд: Bandini Industrie Страницы: 2

Бренд: Key Automation Страницы: 60

Бренд: Nice Страницы: 47

EaziClean BCO-50

Бренд: Lincoln Redco Страницы: 2

Spacemaker Gizmo GC200 Series

Бренд: Black & Decker Страницы: 5

Бренд: CAME Страницы: 8

Бренд: CAME Страницы: 24

Бренд: CAME Страницы: 16

Бренд: Gatex Страницы: 20

Бренд: CAME Страницы: 28

Бренд: RAWLINK Страницы: 73

Бренд: Wayne-Dalton Страницы: 21

Бренд: cedamatic Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды