background image

 

IMPORTANT SAFETY INSTRUCTIONS 

THE FOLLOWING SAFETY INSTRUCTIONS RELATE TO THE OPERATION OF 
THE  PANTHEON COMMERCIAL ROLLING DOOR OPERATOR 
 
WARNING !! —TO REDUCE THE RISK OF DEATH OR SEVERE INJURY ALL OF 
THE FOLLOWING INSTRUCTIONS  MUST BE READ, ACKNOWLEDGED AND 
ADHERED TO. 
 

x

DO NOT 

allow children to operate the control panel, wall switch or any remote 

control device connected to or designed to operate the rolling door. 

x

DO NOT 

attempt to operate the rolling door unless you have a clear and 

unobstructed view of the door and the surrounding area. 

x

DO NOT

 operate the rolling door if there are children or persons in the vicinity of 

the opening—wait until the area is clear before operating. 

x

DO NOT

 cross the path of a moving rolling door. 

x

TEST 

any safety features of the operator on a regular monthly basis and in the 

even that a fault is determined—discontinue use of the door and operator until 
such time as the problem is rectified by a qualified technician. 

x

LOCAL AND STATE 

safety regulations may require the connection of an external 

entrapment protection device when certain optional operational features of the 
operator are selected. These include the use of timer devices, auto close feature, 
momentary contact to close and the use of remote control transmitters. 

x

PRIOR TO OPERATING

 the door—ensure that you are familiar with the full 

operational characteristics of the rolling door and operator and understand the 
safety requirements. 

x

DO NOT 

attempt any repairs, modifications or adjustments to the door or 

operator—all such issues should be attended to by a suitably qualified technician. 

x

IF POSSIBLE 

only activate the manual release lever when the rolling door is in the 

closed position. Weak or broken springs may allow the door to fall rapidly. In all 
cases use caution when engaging the manual release. 

x

IF ANY DOUBT 

exists with any feature or function of the door or operator—consult 

the manufacturer, agent, distributor or authorized installation technician. 

x

KEEP

 these instructions in a safe and suitable location for reference and ensure 

that all personnel are advised accordingly . 

Содержание Pantheon

























Отзывы: