manualshive.com logo in svg

Janus Pantheon, Руководство пользователя

Поделиться
Скачать
Janus Pantheon Скачать руководство пользователя страница 7

7 

 
 

Fuse Protection 

• 

Replaceable “slow blow” type fuses are fitted where required to provide protection for the circuit 
board and where external accessories require DC power from the logic controller 

 

 
 

 

 
 
 
 
 

 

External Wiring Protection Array 

• 

A specifically designed array of diodes and current limiting resis-
tors intended to limit the effects of poor or incorrect site wiring to 
external devices 

• 

In the unintentional event of incorrect wiring connections, the op-
erator will not function 

 
 

External Entrapment Protection—Monitoring 

• 

Effective as of August, 2010, UL325  will deem that where an ex-
ternal entrapment device is connected as required, it shall be monitored by the software 

• 

The logic controller will not permit the operator to function to close if the entrapment device is 
faulty unless the DOWN button is activated by constant contact 

 
 

Toroidal Transformer 

• 

Superior performance and consistent power supply 

• 

More efficient than traditional “iron block” style  

• 

Manufactured to exceed UL specifications 

 

 
 

Main Power Fuse and Isolation Switch 

• 

Designed to allow the qualified technician to switch the main power 

when making external connections to the circuit board 

• 

Fuse protection for main supply 110V AC  

 
 

DC OUTPUT POWER 
PROTECTION FUSE FOR 
EXTERNAL ACCESSO-
RIES

 

CIRCUIT BOARD 
POWER INDICA-
TOR LED LIGHT 
AND PROTECTION 
FUSE

 

Содержание Pantheon

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды