Janome JSR4400N SCARASeries Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 99

Janome JSR4400N SCARASeries Скачать руководство пользователя страница 34

Features II JS/JSR4400N SCARA Robot

JSG GANTRY Robot

JR2000N Desktop Robot

30

FUNCTIONS

Robot System Functions

You can use the built-in variables (which are built into the robot system) and the user-defined variables
(which can be freely defined by the user).
The user-defined variables other than local variables (variables effective only in defined point job data
which are defined by the

declare

command) are defined in the Customizing mode. (See the operation

manual

Features IV

for details of the Customizing mode.)

The functions built into the robot system are as follows:

Type Identifier

Description

num

currentMainProgNumber ()

Currently performed main program number

num

currentSubProgNumber ()

Currently performed sub program number

num

currentPointNumber ()

Currently performed point number

num

currentArmX ()

Current X-coordinate [mm]

num

currentArmY ()

Current Y-coordinate [mm]

num

currentArmZ ()

Current Z-coordinate [mm]

num

currentArmR ()

Current R-coordinate [deg]

num

currentCmdArmX ()

Current command X-coordinate [mm]

num

currentCmdArmY ()

Current command Y-coordinate [mm]

num

currentCmdArmZ ()

Current command Z-coordinate [mm]

num

currentCmdArmR ()

Current command R-coordinate [deg]

num

numCOM (COM port number)

Data byte count of COM receiving port

num isConditionData

(n)

Display whether the specified condition data number
is available (1) or not (0).

str strCenterLCD

(a)

Adjust the strings on the teaching pendant LCD
(centering).

str strRightLCD

(a)

Adjust the strings on the teaching pendant LCD (right
justification).

str strPlusRLCD

(a,b)

Teaching pendant LCD: Right priority; Items on the
right are displayed in full if there is an overlap.

str strPlusLLCD

(a,b)

Teaching pendant LCD: Left priority; Items on the left
are displayed in full if there is an overlap.

num getSystemPTPmoveTime

()

Valid only for [Job while Moving].
Time required for the current PTP drive [sec]

num getSystemPTPrestTime

()

Valid only for [Job while Moving].
Time left before the current PTP drive ends (reaching
the destination) [sec]

«
...
32
33
34
35
36
...
»

Содержание JSR4400N SCARASeries




































































































Отзывы:

Нет отзывов