Janome 6260QC - Скачать руководство пользователя

Страница: 3 / 35

What to Do When

Condition

Cause

How to fix

Reference

1. Skipped

1. Needle is not inserted

Insert the needle properly.

stitches

properly.

2. Needle is bent or worn.

Change the needle.

3. Incorrectly threaded.

Rethread.

4. Needle or thread is

Use the recommended

inappropriate for fabric

sewing needle and thread.

being sewn.

5. Sewing on stretch fabric.

Use a #11 blue tip needle.

6. Presser foot pressure is too

Adjust the presser bar level to

weak.

make the pressure stronger.

7. Inappropriate needle bar

See mechanical adjustment

p.15

height.

“needle bar height”.

8. Inappropriate needle to

See mechanical adjustment

p.16

shuttle timing.

“needle to shuttle timing”.

9. Inappropriate needle to

see mechanical adjustment

p.17

shuttle clearance.

“needle clearance to shuttle.”

2. Fabric not

1. Presser foot pressure is too

Adjust the presser bar level to

moving

weak.

make the pressure stronger.

2. Incorrect f.d. height.

See mechanical adjustment

p.14

“feed dog height.”

3. F.d. is in down position.

Raise the f.d.

4. Thread on bottom side of

Make sure to bring both needle

fabric is jammed up.

and bobbin thread under the

foot when starting sewing.

5. Feed dog teeth are worn.

Change the feed dog.

Содержание 6260QC -




































Результаты поиска

Содержание 6260QC -

Отзывы:

Похожие инструкции для 6260QC -

Бренды по названию

Популярные бренды

Janome 6260QC -, Руководство по обслуживанию

Результаты поиска

Содержание 6260QC -

Отзывы:

Похожие инструкции для 6260QC -

Бренды по названию

Популярные бренды