manualshive.com logo in svg

Janome 6260QC -, Руководство по обслуживанию

Поделиться
Скачать
Janome 6260QC - Скачать руководство пользователя страница 25

Replacing A-Board and Fuse

To Replace the A-board:

1. Remove the rear cover (see page 9).

2. Remove the 3 setscrews (A) and unplug the connectors from the A-board.

3. Remove the 6 setscrews (B) and 2 setscrews (C) then remove the board supporter and function button

frame.

4. Remove the 2 setscrews (D) and remove the board case then replace the A-board.

Note:

Static electricity may damage the A-board. When handling the A-board, use a static dissipative wristband

and anti-static tabletop mat.

Setscrew (A)

Setscrew (B)

Setscrew (B)

Board supporter

Function button frame

Setscrew (B)

Setscrew (A)

Setscrew (B)

Setscrew (B)

Setscrew (A)

Setscrew (B)

A - board

Setscrew (C)

Setscrew (C)

A - board case

Setscrew (D)

Setscrew (D)

Fuse

A - board

F3 AC250V 2.5A

(#000144605)

F2 AC250V 3.15A

(#000182904)

F1 AC250V 2.5A

(#000144605)

To replace the fuse:

Pry out the fuse with a screwdriver.

Replace the fuse and push it down into the fuse clip.

23

Содержание 6260QC -




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды