Janome 6260QC - Скачать руководство пользователя

Страница: 23 / 35

01)

7-segment LED

02)

Mode LED

03)

Button

04)

Bobbin winder

switch

05)

Not applicable to

this model

06)

Buttonhole Sensor

Sensor

Defective Condition

Correct Condition

Procedure

Step and items

to check

Turn on the power switch while

simultaneously pressing the

needle up/down button and the

reverse button. Press the reverse

button five times to select menu

item “6”. Press the needle up/

down button: the LED indicates

“01” for one second. If you don’t

press the reverse button within

2 . 5 s e c o n d s , t h e m a c h i n e

automatically reverts to normal

sewing mode.

B e e p s o u n d s w h e n t h e

button is pressed.

LED displays “8.8.” And it

blinks in one second

Intervals.

No beep sound

Does not enter self-diagnostic

mode.

LED does not blink on or off.

1. Replace A-board.

LED

Press needle up/down button,

LED displays “02” for one

second.

7-segment LED displays

“Ld” and 3 mode LEDs

b l i n k i n o n e s e c o n d

intervals.

LED does not blink on or off.

1. Replace A-board.

LED displays

Button number is displayed

when the button is pressed

LED display is different from

that shown to the left.

1. Replace A-board.

Button

S5 S6 S7

Press needle up/down button,

LED displays “04” for one

second.

Move the bobbin winder spindle

to the right.

Return it to the left.

LED displays “II”.

(Left)

(Right)

LED display is different from

that shown to the left.

1. Adjust bobbin winder switch

position.

2. Replace bobbin winder

switch.

3. Replace A-board.

LED display is different from

that shown to the left.

1. Adjust buttonhole sensor

position

2. Replace buttonhole sensor.

3. Replace A-board.

Skip this step by pressing the

needle up/down button

Press needle up/down button,

LED displays “06” for one

second.

Lower the buttonhole lever.

Move the buttonhole lever back

and forth.

When the buttonhole lever

is pulled, LED displays “H”.

When the buttonhole lever

is free (positioned in the

center), LED displays “L”.

When the buttonhole lever

is pushed, LED displays

“H”.

Press needle up/down button,

LED displays ”03” for one

second.

Press buttons S1 to S8.

Содержание 6260QC -




































Результаты поиска

Содержание 6260QC -

Отзывы:

Похожие инструкции для 6260QC -

Бренды по названию

Популярные бренды

Janome 6260QC -, Руководство по обслуживанию

Результаты поиска

Содержание 6260QC -

Отзывы:

Похожие инструкции для 6260QC -

Бренды по названию

Популярные бренды