Jandy APURE35 Скачать руководство пользователя страница 21

Page 21

4.7.3  How Much Salt to Use 

Use salinity test strips, a TDS/salinity meter, or another reliable method to test the salinity of the pool water. Once the 

existing salinity has been established, use Table 1 to determine the amount of salt to add to reach the desired level. Be 

conservative when adding salt as it is easier to add more if needed than it is to dilute if there is too much salt. 

•  4,000 ppm of salt is recommended for optimum water conditions.
•  Low salt concentration below 3,000 ppm will cause premature cell failure.
•  High salt concentration above 6,000 ppm may cause corrosion damage to pool fixtures.

4.7.4  How to Add Salt to the Pool 

1.  Turn on pump to circulate pool water.
2. 

IMPORTANT - Turn the 

power pack 

off by pressing the ON/Off button (OFF will be displayed on the screen).

3.  Test the water for salinity level using test strips, electronic meter, or by your local pool professional.

4.  Use the Table 1 to determine the amount of salt to add.  Be conservative when adding salt as it is easier to add 

more if needed than it is to dilute if there is too much salt.

5.  Broadcast salt into pool. Do not add through skimmer, main drain, or surge tank. Brush the salt around the pool to 

facilitate dissolving. Circulate filter system for 24 hours to ensure even distribution.

6.  After 24 hours, verify correct salt reading by testing the water salinity level using test strips, electronic meter, or 

by your local pool professional.

7.  When the salinity level is correct, turn the power pack on.  Press the OUTPUT button to set the desired production 

rate.

NOTE

 

For a new pool or newly resurfaced pool it is recommended to wait at least 30 days (surface should be 

completely cured) before adding salt. Follow the pool surface manufacturers guidelines for your 

 

particular pool. For vinyl and fiberglass pools, salt can be added at start up

.

Table 1. 

Approximate Pounds and Kilograms of Salt Needed to Obtain 4.0 gpl (4,000 ppm) 

Current

Salt

Level

ppm

Pool/Spa Size - US Gallons (Litres)

10,000 g

(38,000 L)

15,000 g

(57,000 L)

20,000 g

(76,000 L)

25,000 g

(95,000 L)

30,000 g

(114,000 L)

35,000 g

(132,000 L)

0

334 lbs (151 kgs)

501 

lbs (227 kgs) 668 lbs (303 kgs) 835 lbs (379 kgs) 1001 lbs (454 kgs)

1168 lbs (530 kgs)

250

313 lbs (142 kgs)

469 

lbs (213 kgs) 626 lbs (284 kgs) 782 lbs (355 kgs)

939 lbs (426 kgs)

1095 lbs (497 kgs)

500

292 lbs (132 kgs)

438 

lbs (199 kgs) 584 lbs (265 kgs) 730 lbs (331 kgs)

876 lbs (397 kgs)

1022 lbs (464 kgs)

750

271 lbs (123 kgs) 407 lbs (185 kgs) 542 lbs (246 kgs) 678 lbs (308 kgs)

814 lbs (369 kgs)

949 lbs (431 kgs)

1000

250 lbs (114 kgs) 376 lbs (170 kgs) 501 lbs (227 kgs) 626 lbs (284 kgs)

751 lbs (341 kgs)

876 lbs (397 kgs)

1250

229 lbs (104 kgs) 344 lbs (156 kgs) 459 lbs (208 kgs) 574 lbs (260 kgs)

688 lbs (312 kgs)

803 lbs (364 kgs)

1500

209 lbs (95 kgs) 313 lbs (142 kgs) 417 lbs (189 kgs) 522 lbs (237 kgs)

626 lbs (284 kgs)

730 lbs (331 kgs)

1750

188 lbs (85 kgs) 282 lbs (128 kgs) 376 lbs (170 kgs) 469 lbs (213 kgs)

563 lbs (256 kgs)

657 lbs (298 kgs)

2000

167 lbs (76 kgs) 250 lbs (114 kgs) 334 lbs (151 kgs) 417 lbs (189 kgs)

501 lbs (227 kgs)

584 lbs (265 kgs)

2250

146 lbs (66 kgs)

219 lbs (99 kgs) 292 lbs (132 kgs) 365 lbs (166 kgs)

438 lbs (199 kgs)

511 lbs (232 kgs)

2500

125 lbs (57 kgs)

188 lbs (85 kgs) 250 lbs (114 kgs) 313 lbs (142 kgs)

376 lbs (170 kgs)

438 lbs (199 kgs)

2750

104 lbs (47 kgs)

156 lbs (71 kgs)

209 lbs (95 kgs)

261 lbs (118 kgs)

313 lbs (142 kgs)

365 lbs (166 kgs)

3000

83 lbs (38 kgs)

125 lbs (57 kgs)

167 lbs (76 kgs)

209 lbs (95 kgs)

250lbs (114 kgs)

292 lbs (132 kgs)

3250

63 lbs (28 kgs)

94 lbs (43 kgs)

125 lbs (57 kgs)

156 lbs (71 kgs)

188 lbs (85 kgs)

219 lbs (99 kgs)

3500

42 lbs (19 kgs)

63 lbs (28 kgs)

83 lbs (38 kgs)

104 lbs (47 kgs)

125 lbs (57 kgs)

146 lbs (66 kgs)

3750

21 lbs (9 kgs)

31 lbs (14 kgs)

42 lbs (19 kgs)

52 lbs (24 kgs)

63 lbs (28 kgs)

73 lbs (33 kgs)

4000

Optimum

Optimum

Optimum

Optimum

Optimum

Optimum 

Содержание APURE35





































Отзывы: