J&M 275-ST страница 31 Скачать руководство пользователя | Manualshive

Страница: 31 / 58

background image

31

2.0 Service

Problems

Solutions

Belt has insufficient output speed or R.P.M. - Air in

hydraulic system.

a. Bleed air out of hydraulic system and fill reservoir (See section

2.6).
b. Look for leaking or cracked fittings.

Belt has insufficient output speed or R.P.M. - Leak in motor, valve

body, or bypass valves.

a. Replace or repair motor, valve body, or bypass valves.

b. Check for proper oil viscosity.
c. Clean and lubricate the brake assemblies

Excessive wear to belt edge - Tracking is off.

a. Adjust belt tension and tracking (See section 2.8).

Excessive wear to belt edge - Rubber skirting is worn or out of place. a. Replace rubber skirting.

b. Adjust rubber skirting.

Boom arm will not move up or down - Engine R.P.M. slow.

a. Increase engine R.P.M.

Boom arm will not move up or down - Hydraulic pump is not

producing sufficient pressure or volume to hydraulic cylinder.

a. Check for pinched or leaking hydraulic lines.

b. Allow hydraulic oil to warm up.
c. Increase engine R.P.M.
d. Hydraulic fluid level low.
e. Hydraulic filter clogged.
f. Check for proper oil viscosity.
g. Check to see if hydraulic pump is worn out
h. Make sure battery is fully charged.
i. Check wiring to valve body and hydraulic pump

Hydraulic unit squeals

a. Check sight glass on hydraulic unit reservoir and fill if necessary.
b. Run engine at reduced speed for 5-10 minutes to warm up oil.
c. Clean/replace filler cap/breather.
d. Clear obstruction in suction hose.
e. Replace plugged/dirty oil filter element.

Hydraulic unit has poor performance at high R.P.M.

a. Clean pressure relief in control valve or replace
b. Check sight glass on hydraulic unit reservoir and fill if necessary.
c. Replace plugged/dirty oil filter element
d. Charge Battery

2.14 Troubleshooting

«
...
29
30
31
32
33
...
»

Содержание 275-ST



























































Отзывы:

Нет отзывов

Похожие инструкции для 275-ST

ACS880-01 Series

Бренд: ABB Страницы: 238

Бренд: Tanco Страницы: 72

Бренд: HABYS Страницы: 16

Бренд: Acterna Страницы: 72

WJHD309A - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 79

Бренд: NARGESA Страницы: 37

Бренд: NARGESA Страницы: 6

RIDA qLine ZG2601

Бренд: R-Biopharm Страницы: 23

Бренд: VelociRAX Страницы: 4

Бренд: ABM Страницы: 17

Бренд: Qtx Страницы: 6

Бренд: Martin Страницы: 202

SeQual Eclipse 5

Бренд: CAIRE Страницы: 2

Бренд: Exalto Страницы: 28

Бренд: PURE Страницы: 16

Бренд: POOL LAB Страницы: 6

Бренд: VividLeds Страницы: 2

Бренд: Leica Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды