J&M 275-ST Скачать руководство пользователя

Страница: 38 / 58

Specifications

Auto Scale Shutoff

In order for the Auto Dispense function to work, the Speed Tender must

be equipped with a factory installed and powered on Weigh-Tronix 640XL

scale indicator with the J&M Mega Remote with Auto Dispense as shown

to the right.

Using the Auto Dispense Feature

Note: The Auto Dispense Feature is only active after you change or confirm the weight

and/or door settings each time the receiver is turned on

• Simply press the Green Auto Dispense(1) button to activate the feature.

• The system will Start the conveyor, open the door, unload within 2-4 Lbs of the desire

weight, close the door and cleanout the conveyor with a single press of a button.

• If filling multiple planter boxes, press the Auto Dispense button again to repeat the

process. This can be done during the conveyor cleanout stage

Setting the desired Auto Dispense Weight

• Press Scroll (2) to enter Auto Dispense menu

• Hold Tare (3) till weight flashes

• Use the Left and Right Navigation buttons to select the digit and the Up and Down

buttons to change the digit

• Hold Tare (3) to Save the desire weight

Selecting the Door to Auto Dispense

• Press Scroll (2) twice to enter the Door Selection menu

• Hold Tare (3) until Door Number is flashing

• Use the Up and Down Navigation buttons to select either door 1 or 2

Door 1 = Front Door

Door 2 = Rear Door

• Hold Tare (3) to Save to door setting

Pairing the J&M Mega Remote to the Receiver

Note: The wireless switch should be in the off position

• Hold Power (4) until the screen displays TEACHING MODE

• Toggle the Wireless Power Switch to On

• The Display will now display “TEACHING COMPLETE” and will return to the live weight display.

TARE

SCROLL

NAVIGATION

DISP.

AUTO

OPEN

CLOSE

FRONT

DOOR

OPEN

CLOSE

REAR

DOOR

CONVEYOR

FRONT

REAR

CONV

START

CONV

STOP

POWER

In order for the Auto Dispense function to work, the Speed Tender must

be equipped with a factory installed and powered on Weigh-Tronix 640XL

scale indicator with the J&M Mega Remote with Auto Dispense as shown

to the right.

J&M Mega Remote

with Auto Dispense

Note: For best accuracy,

RUN THROTTLE AT 80% OR HIGHER

J&M Manufacturing Co., Inc. - Fort Recovery, Ohio - 419.375.2376 - www.jm-inc.com

Auto Dispense

Instruction

J&M Mega Remote

For use with the Weigh-Tronix 640XL scale package

and J&M Mega Remote Control Installed

Please consult your operators manual

for more detailed information

Pairing the J&M Mega Remote to the

Receiver

Note: The wireless switch should be in the off position

• Hold Power until the screen displays TEACHING MODE

• Toggle the Wireless Power Switch to On

• The Display will now display “TEACHING COMPLETE” and will return to the live weight display.

Using the Auto Dispense Feature

Note: The Auto Dispense Feature is only active after you change or

confirm the weight and/or door settings each time the reciever is turned on

• Simply press the

Green

Auto Dispense button to activate

the feature.

• The system will Start the conveyor, open the door, unload within

2-4 Lbs of the desire weight, close the door and cleanout the

conveyor with a single press of a button.

• If filling multiple planter boxes, press the Auto Dispense button again

to repeat the process.

This can be done during the conveyor cleanout stage

Selecting the Door to Auto Dispense

•

Press Scroll twice to enter the Door Selection menu

• Hold Tare until Door Number is flashing

• Use the Up and Down Navigation buttons to select either door 1 or 2

Door 1 = Front Door

Door 2 = Rear Door

• Hold Tare to Save to door setting

Setting the desired Auto Dispense Weight

• Press Scroll to enter Auto Dispense menu

• Hold Tare till weight flashes

• Use the Left and Right Navigation buttons to select the digit and

the Up and Down buttons to change the digit

• Hold Tare to Save the desire weight

J&M

MEGA REMOTE

Содержание 275-ST



























































Результаты поиска

Содержание 275-ST

Отзывы:

Похожие инструкции для 275-ST

Бренды по названию

Популярные бренды

J&M 275-ST, Руководство оператора

Результаты поиска

Содержание 275-ST

Отзывы:

Похожие инструкции для 275-ST

Бренды по названию

Популярные бренды