manualshive.com logo in svg

J&M 275-ST, Руководство оператора

Поделиться
Скачать
J&M 275-ST Скачать руководство пользователя страница 20

20

2.0   Service

2.3 Tire Pressure

The following is to be used as a general guide for tire inflation. Figures can vary depending on specific brand of tire used. It is im-
portant that tires are inspected before and after unit is loaded. Start with the minimum pressure indicated. The tire should stand up 
with no side wall buckling or distress as tire rolls. Do not exceed maximum recommended tire pressure. 80 psi is the cold rating on 
the tire that is standard for the Speed Tender. J&M also recommends to rotate your tires front to back (not side to side) every 1,200 
miles or 12 months (whichever comes first) for longer tire life.  Figure 2.3 below is a troubleshooting chart used to ensure the tires 
wear evenly.

 

2.4 Tightening Lugnuts

Torque lug-nuts on new and removed wheels to 220 ft. lbs. after the first 10, 25, and 50 miles of driving, then recheck torque every 
50 hours or every year, whichever comes first. 
     

Figure 2.3

Содержание 275-ST



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды