background image

SELECTION OF SITE

Ø

Proper space should be there for placement and opening of doors of the  

 

Silent DG set.

Ø

There  should  be  atleast  1.5  meter  free  space  around  the  DG  set  for 

 

proper operation and maintenance.

Ø

There should be cross ventilation of air to ensure proper cooling of DG 

 

set.  Exhaust gases and hot air discharge should not re-circulate inside 

 

the acoustic enclosure (canopy). 

Ø

 

If  Genset  is  to  be  installed  in  the  room,  please  ensure  proper  cross   

 

ventilation and surrounding space.

Ø

There should be no restriction for fresh air suction and hot air discharge.  

 

If  2 nos. DG sets are installed at the site, ensure that hot air outlet of the 

 

one DG set does not become the fresh air intake of the 2nd DG set.

Ø

 

If Genset is to be installed in the basement, please ensure ventilation 

 

with respect to Air requirement and clear space for every maintenance. 

Ø

Distance between two SDG set should be minimum 1.5 meters.

Ø

A low height shelter for the Silent DG Set should be avoided. It should 

 

not obstruct the hot air outlet, shelter height minimum 1.5 meter or 

 

equal to height of genset

 

Ø

It is preferable to install the DG set in an open area.  No shade (roof)  is

 

required  over  it.    However,  if  the  AMF  Panel  is  outside  the  Acoustic   

 

Enclosure,  then a shelter  is recommended for the AMF Panel. 

Ø

For Roof Top Installation, ensure that the civil structure is capable to 

 

bear the static and dynamic load of DG set.  The load of the Silent DG set 

 

should be borne by Columns and  Beams of the building. 

Ø

Proper space should be there for Earthing.

Ø

If there are no space constraints, the DG set should be placed near the 

 

distribution panel.

Ø

The DG set should be located away from polluted surroundings such as 

 

corrosive  fumes,  cement  dust,  fibres,  cotton  and  toxic  chemicals  to 

 

avoid overheating of the  D.G. Set.

Ø

 

There should be sufficient space around the Genset to avoid resonance 

 

and echo effect which contributes to abnormal sound from Genset.

Ø

 

The space should be open without any obstacles.

1

JAKSON & CO.

Содержание JakPower Kirloskar Koel Green EA10 G1





































Отзывы: