JAI BB-500 GE Скачать руководство пользователя

Страница: 45 / 73

BM-500GE / BB-500GE

Trigger Selector

This can be selected from FrameStart or TransferStart.



FrameStart

The trigger pulse can take one frame capture.



TransferStart

The trigger pulse can read out the image stored in the frame memory. This is used for the

delayed Readout

TriggerMode

This selects either trigger mode (ON) or continuous mode (OFF).

TriggerSoftware

This is one of the trigger sources which enables trigger commands to be created using
software. In order to use TriggerSoftware, TriggerSource should be set at Software.

TriggerSource

The trigger source can be selected from the following signals.

TriggerActivation

This can set how the trigger is activated.



RisingEdge: The trigger is effective at the rising edge of the pulse.



FallingEdge: The trigger is effective at the falling edge of the pulse.

ExposureMode

This can select the exposure mode.



Timed: The exposure is set in units of

seconds or lines.

Содержание BB-500 GE










































































Результаты поиска

Содержание BB-500 GE

Отзывы:

Похожие инструкции для BB-500 GE

Бренды по названию

Популярные бренды

JAI BB-500 GE, Руководство пользователя

Результаты поиска

Содержание BB-500 GE

Отзывы:

Похожие инструкции для BB-500 GE

Бренды по названию

Популярные бренды