JAI BB-500 GE Скачать руководство пользователя | Manualshive

Страница: 41 / 73

background image

BM-500GE / BB-500GE

39

The below calculating formula shows the relationship between the PE value used by the
camera for the different readout modes and the value entered in register 0xA018.
Due to round down figure, some errors may occur.

The relation between PE value and Time Abs.
Normal readout       PE= 2 + INT (Exposure time -64) µs / (1924/60000000)
V Binning readout    PE= 2 + INT (Exposure time -71.692) µs / (2524/60000000)
INT means round down.

The following table shows minimum value and maximum value for each readout mode.

Minimum value

Maximum Value

Normal Scan

64.13 us

66.442 ms

2/3 Partial Scan

64.13 us

49.736 ms

1/2 Partial Scan

64.13 us

41.495 ms

1/4 Partial Scan

64.13 us

29.117 ms

1/8 Partial Scan

64.13 us

22.960 ms

V-Binning Scan

84.13 us

43.708 ms

GPIO in combination with Pulse Width trigger

More precise exposure time can be obtained by using GPIO in combination with Pulse Width
mode. The clock generator and counter can be programmed in very fine increments.
As for the setting example, refer to chapter 6.5.1.

9.2. Pre-process functions

BM-500GE/BB-500GE has several pre-
processing functions. The output from
the camera is selectable to 8, 10 or 12-
bit but video is digitized to 14 bits
quantization.
The pre-processing functions make use
of the 14 bit video. Featured functions
are: Bayer color white balance, R/L
channel balance, gain control and LUT
(Look Up Table) for Gamma and Knee
correction.

9.2.1 Bayer White Balance ( Register

0xA0D0)

Normally, the raw Bayer color signals
are sent to the host as they are. In the
host, the signals are interpolated to
generate an RGB image and perform
white balance.
In order to offload the host, the BB-
500GE can adjust Gr, R, Gb and B levels
individually to get the white balance
for the Bayer output signal. The gain is
fixed to 1.0 for BM-500GE.
Note: Bayer white balance must be set at Normal mode.

«
...
39
40
41
42
43
...
»

Содержание BB-500 GE










































































Отзывы:

Нет отзывов

Похожие инструкции для BB-500 GE

Бренд: Canon Страницы: 2

EOS 5D Mark III

Бренд: Canon Страницы: 19

Бренд: Canon Страницы: 22

Бренд: Canon Страницы: 2

EOS 1D Mark III

Бренд: Canon Страницы: 6

Бренд: Canon Страницы: 458

EOS 10D Digital

Бренд: Canon Страницы: 12

EOS 10D Digital

Бренд: Canon Страницы: 32

EOS 10D Digital

Бренд: Canon Страницы: 182

Digital IXUS I5

Бренд: Canon Страницы: 2

Digital IXUS 950 IS

Бренд: Canon Страницы: 37

Digital IXUS I5

Бренд: Canon Страницы: 160

Бренд: Canon Страницы: 388

Digital IXUS 900 TI

Бренд: Canon Страницы: 2

DIGITAL IXUS 70

Бренд: Canon Страницы: 2

Digital IXUS 60

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 76

Бренд: Canon Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды