Jäger F120-H824.11 S11RW2V Скачать руководство пользователя | Manualshive

Страница: 31 / 52

background image

Installation

Item no. 10408017, Revision 05

31 ( 52 )

8

Installation

Before installation:

Ü

Check the HF spindle for damage and ensure that it is complete.

If the HF spindle has been stored for a long period:

Ü

Carry out all steps in the Commissioning after storage section.

8.1

Installing the HF spindle

Connect media and cables with a

flexible connection.

Complete the following steps in sequence to install the HF spindle:

Ü

Remove the sealing plugs that protect the connections against damage
and contamination during transportation.

Ü

Instead of these sealing plugs, install the appropriate hose fittings.

Ü

Install the corresponding hoses in the hose fittings

Ü

Make sure that the connections are flexible and free of strain.

Ü

Seal all connections for compressed air axially in relation to the tightening
direction.

Ü

Seal all connections for cooling water axially in relation to the tightening
direction.

Ü

If the HF spindle is equipped with sealing air:

Ä

Make sure that no air flow can occur in the bearing area.

Ä

Always use sealed cable boxes when connecting electrical lines.

Ü

Mount the HF spindle on the machine.

Ü

Connect the hoses to the connection of the respective media.

Ü

Remove the protective cap that protects the shaft against damage and
contamination during transportation.

Ü

Connect the connector of the operating connection lines to the relevant
connection of the HF spindle and to the frequency converter.

Ü

Lock the connectors.

«
...
29
30
31
32
33
...
»

Содержание F120-H824.11 S11RW2V





















































Отзывы:

Нет отзывов

Похожие инструкции для F120-H824.11 S11RW2V

Бренд: Bartscher Страницы: 22

Бренд: Rangevision Страницы: 31

Бренд: Camozzi Страницы: 2

Бренд: Oktober Страницы: 22

Бренд: Facsimile Страницы: 16

Бренд: BACtrack Страницы: 16

Бренд: Olsen Страницы: 4

Dominator Series

Бренд: Falcon Страницы: 31

Бренд: Fakir Страницы: 22

Бренд: Safety 1st Страницы: 4

Бренд: Safety Engineering Страницы: 5

Бренд: Kelvin Страницы: 30

Бренд: RAM Страницы: 4

Бренд: Analogue Solutions Страницы: 64

Power System KPS-US

Бренд: Keys Fitness Страницы: 8

Бренд: Sammode Страницы: 12

Бренд: Sanela Страницы: 5

Бренд: Osprey Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды