manualshive.com logo in svg

Jäger F120-H824.11 S11RW2V, Руководство пользователя

Поделиться
Скачать
Jäger F120-H824.11 S11RW2V Скачать руководство пользователя страница 16

Technical description

Item no. 10408017, Revision 05

16 ( 52 )

5.8

Leakage

Note: Damage to the HF spindle due to leakage.

Cooling lubricant may enter the HF spindle through the bearing of the inter-
nal coolant supply and destroy it:

q

If the internal coolant supply is operated in the lower pressure range.

q

If the pressure of the cooling medium builds up slowly.

u

Use leakage monitoring to protect the HF spindle from damage.

5.8.1

Internal coolant supply, vertical installation

Example of design: Leakage

Leakage

Screw-in depth

1

High Frequency Spindle

max. 6 mm

2

Internal coolant supply

max. 6 mm

Ü

Remove the sealing plugs that protect the connections against damage
and contamination during transportation.

Ü

Instead of these sealing plugs, install the appropriate hose fittings.

Ü

Install the corresponding hoses in the hose fittings

Ü

Route the leakage hose with a falling gradient so that the leakage can be
discharged.

Ä

Angle: at least 15°.

Ü

Route away the leak to avoid backing up.

Содержание F120-H824.11 S11RW2V





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды