Jadak N Series Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 90

background image

JADAK flexpoint™ HS-‐‑1M User’s Manual

Page 71

Statement of Agency Compliance

This HS-1M  complies with  part  15  of  the  FCC  Rules.  Operation  is subject  to  the  following  two
conditions:  (1) this HS-1M  may not  cause  harmful  interference  and  (2) this HS-1M  must  accept
any interference  received,  including  interference  that  may cause  undesired  operation.

FCC Class B Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

HS1-M pursuant  to  part  15  of  the  FCC  Rules.  These  limits are  designed  to  provide  reasonable
protection  against  harmful  interference  in  a  residential  installation.  This equipment  generates,
uses,  and  can  radiate  radio  frequency energy and,  if  not  installed  and  used  in  accordance  with
the  instructions,  may cause  harmful  interference  to  radio  communications.  However,  there  is no
guarantee  that  interference  will  not  occur in  a  particular installation.  If  this equipment  does cause
harmful  interference  to  radio  or television  reception,  which  can  be  determined  by turning  the
equipment  off  and  on,  the  user is encouraged  to  try to  correct  the  interference  by one  or more  of
the  following  measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio or television technician for help.

Caution:

Any changes or modifications made to this HS1-M, which are not expressly

approved

by JADAK, LLC may void the user’s authority to operate the equipment.

Note:

To maintain compliance with FCC Rules and Regulations, cables connected to this

HS1-M must be shielded cables, in which the cable’s shield wire(s) have been grounded (tied) to
the connector shell.

«
...
70
71
72
73
74
...
»

Содержание N Series



























































































Отзывы:

Нет отзывов

Похожие инструкции для N Series

Бренд: Winkhaus Страницы: 5

Бренд: Polaroid Страницы: 2

Бренд: Icarus Страницы: 40

StrataScan 2755-LHR-3C

Бренд: Allen-Bradley Страницы: 68

ePort G9 Card Reader

Бренд: USA Technologies Страницы: 9

Бренд: ACS Страницы: 42

Бренд: Farpointe Data Страницы: 2

Бренд: Cognex Страницы: 16

Бренд: Omron Страницы: 71

MicroHAWK V320-F

Бренд: Omron Страницы: 56

Бренд: Scantech Страницы: 97

Бренд: Access Interfacing Solutions Страницы: 33

Бренд: ARKSCAN Страницы: 54

Бренд: Brivo Страницы: 2

Бренд: SICK Страницы: 134

HT660 Wireless edition

Бренд: Unitech Страницы: 90

GRYPHON D Series

Бренд: Datalogic Страницы: 32

GX-2408T Series

Бренд: Gainscha Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды