Jadak N Series Скачать руководство пользователя страница 85

Страница: 85 / 90

JADAK flexpoint™ HS-‐‑1M User’s Manual

Page 84

Barcode

AIM ID

AIM ID Modifiers

GS1 DataBar Family

No  option  specified  at  this  time.  Always  transmit  0.  GS1
DataBar  and  GS1  DataBar  Limited  transmit  with  an  Application
Identifier  “01”.

Note:

In GS1-128 emulation mode, GS1 DataBar is

transmitted using Code 128 rules (i.e., ]C1).

Example:

A GS1 DataBar bar code 0110012345678902 is

transmitted as

00110012345678902.

Codabar

0 No check digit processing.

1 Reader has checked check digit.

3 Reader has stripped check digit before transmission.

Example:

A Codabar bar code without check digit, 4123, is

transmitted as

]F0

4123

Code 93

0 No options specified at this time. Always transmit 0.

Example:

A Code 93 bar code 012345678905 is transmitted

]G0

012345678905

Code 11

0 Single check digit

1 Two check digits

3 Check characters validated but not transmitted.

Interleaved 2 of 5

0 No check digit processing.

1 Reader has validated check digit.

3 Reader has validated and stripped check digit.

Example:

An I 2 of 5 bar code without check digit, 4123, is

transmitted as

]I0

4123

PDF417, Macro PDF417, Micro
PDF417

0 Reader set to conform to protocol defined in 1994 PDF417
Symbology specifications.

Note:

When this option is transmitted, the receiver cannot

reliably determine whether ECIs have been invoked or
whether data byte 92

DEC

has been doubled in transmission.

1 Reader set to follow the ECI protocol (Extended Channel
Interpretation). All data characters 92

DEC

are doubled.

2 Reader set for Basic Channel operation (no escape
character transmission protocol). Data characters 92

DEC

are

not doubled.

Note:

When decoders are set to this mode, unbuffered

Macro symbols and symbols requiring the decoder to convey
ECI escape sequences cannot be transmitted.

3 The bar code contains a GS1-128 symbol, and the first
codeword is 903-907, 912, 914, 915.

4 The bar code contains a GS1-128 symbol, and the first
codeword is in the range 908-909.

5 The bar code contains a GS1-128 symbol, and the first
codeword is in the range 910-911.

Example:

A PDF417 bar code ABCD, with no transmission

protocol enabled, is transmitted as ]L2ABCD.

Содержание N Series



























































































Результаты поиска

Содержание N Series

Отзывы:

Похожие инструкции для N Series

Бренды по названию

Популярные бренды

Jadak N Series, Руководство пользователя

Результаты поиска

Содержание N Series

Отзывы:

Похожие инструкции для N Series

Бренды по названию

Популярные бренды