background image

7

OWNER'S MANUAL

12 ft / 4 m

Midpoint of the long side of pool

Figure 3.  Pool Entry Point for Optimal Patterning

2.  Submerge cleaner vertically and turn upside 

down until the bubbles stop to remove any air 
trapped inside (Figure 4).

3.  When the bubbles stop, allow the cleaner to sink 

to the bottom of the pool.

Figure 4.  Submerge and Remove Trapped Air

4.  Verify the cleaner is sitting right-side up on the 

bottom of the pool. Remove additional air if the 

cleaner is still floating.

5.  Spread all of the floating cable carefully in the 

pool, ensuring there are no kinks or coils. 

Use only as much cable as you need to reach the 

farthest wall. This can help prevent cable tangling 
(Figure 5).

Figure 5.  Spread Floating Cable to Prevent 

Tangling

4.2 

START / STOP CLEANING

1.  Press On/Off button to begin or interrupt cleaner 

operation (Figure 6).

ON / 

OFF

Figure 6.  Begin Cleaning

2.  Press SELECT button to choose between SMALL 

POOL and LARGE POOL. Cleaning duration for 
a small pool is 1 hour; for a large pool, duration is 
2 hours (Figure 7).

3.  Cleaner will begin to move.

= 1 Hour Shut-off

= 2 Hour Shut-off

Figure 7.  Select Pool Size and Duration

Содержание 63659













Отзывы: