Jacobsen HR 5111 Скачать руководство пользователя страница 324

Страница: 324 / 339

DISASSEMBLY (See Figure 12D-6)

1. Remove blade and adapter.

2. Remove square drive key.

3. Remove shaft protector.

4. Remove large lock ring.

5. Install blade with adapter.

6. Pull spindle shaft and guide from housing.

NOTE

A suction will be felt when pulling the guide from
the housing. The suction will be broken when
O-ring clears the housing.

7. Remove blade with adapter.

8. Remove small lock ring.

9. Remove spacer, seal and spindle shaft.

NOTE

Perform Step 10 only if spindle housing bearing
is to be changed.

10. Remove motor assembly from spindle housing.

Do not disassemble motor.

11. Remove spindle shaft bearing.

REASSEMBLY (See Figure 12D-6)

1. Install spindle bearing if removed.

2. Install motor onto spindle housing. Torque bolts to

18 ft-lbs. (24 N.m).

3. Install spindle shaft.

4. Install spindle shaft guide.

5. Install large snap ring.

6. Install seat (lip to the inside), spacer and small

lock ring.

7. Install shaft protector and square drive key.

8. Install blade with adapter. Torque center blade

screw to 75 ft-lbs. (102 N.m).

9. Check torque of blade mounting screws, torque to

35–40 ft-lbs. (47–54 N.m).

ATTACHMENTS

SECTION 12D. MOWERS

12D-6

Figure 12D-6. Spindle Assembly

Содержание HR 5111




















































































































































































































































































































































Результаты поиска

Содержание HR 5111

Отзывы:

Похожие инструкции для HR 5111

Бренды по названию

Популярные бренды

Jacobsen HR 5111, Инструкции по обслуживанию и ремонту

Результаты поиска

Содержание HR 5111

Отзывы:

Похожие инструкции для HR 5111

Бренды по названию

Популярные бренды