Jacobsen HR 5111 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 339

background image

RADIATOR (See Figure 3D-2)

CHANGING COOLANT

1. Open drain cock (1) and radiator cap (2) and drain

coolant into a clean container.

2. Flush the inside of the radiator (3) with clean water.

NOTE

Always mix anti-freeze with the cooling water.
Mixture ratios differ with the anti-freeze manu-
facturer and temperature. Follow the instructions
of each manufacturer. However, do not exceed
a 50/50 mixture of anti-freeze to water.

CLEANING RADIATOR CORE

When dust enters between fins and tubes, blow out
with air, then wash with tap water under pressure.

NOTE

Never use a screwdriver or other pointed tool for
cleaning. It may damage the core tubes of the
radiator.

Open access door at bottom of radiator to allow trash
to fall out during cleaning.

REMOVAL (See Figure 3D-2)

1. Loosen wing nuts holding oil cooler in place and

tilt oil cooler out of the way.

2. Remove hardware securing fan shroud to radiator

and move shroud back over fan.

3 Open drain cock (1), remove radiator cap (2) and

drain the coolant.

4. Disconnect the inlet and outlet hoses by loosen-

ing hose clamps (3).

5. Disconnect overflow tube at radiator cap.

6 Remove attaching hardware (4 and 5).

7. Inspect weatherstrip (7). Replace if damaged.

INSTALLATION (See Figure 3D-2)

1. Install weatherstrip (6) if removed.

2. Place the radiator (3) on frame and secure with

attaching hardware (4 and 5).

3. Connect overflow coolant tube.

4. Connect the inlet and outlet hoses; tighten hose

clamps (3).

5. Close drain cock (1) and fill the radiator with clean

distilled water/anti-freeze mixture.

NOTE

Always mix anti-freeze with the cooling water.
Mixture ratios differ with the anti-freeze manu-
facturer and temperature. Follow the instructions
of each manufacturer. However, do not exceed
a 50/50 mixture of antifreeze to water.

6. Secure fan shroud to radiator with attaching hard-

ware.

7. Secure oil cooler in place with wing nuts and

washers.

ENGINE

SECTION 3D. DIESEL ENGINE

3D-2

!

CAUTION

Never open radiator cap (2) while engine is run-
ning or soon after it stops. Hot water sometimes
shoots out if the radiator cap is opened while the
engine is hot.

Figure 3D-2. Radiator Service

«
...
32
33
34
35
36
...
»

Содержание HR 5111




















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HR 5111

Бренд: Baroness Страницы: 199

Wheel Horse 265-6

Бренд: Toro Страницы: 44

Бренд: Simplicity Страницы: 54

Бренд: Hayter Страницы: 40

Бренд: Snapper Страницы: 66

Бренд: MTD Страницы: 20

E-Rider R85.1 Li

Бренд: AL-KO Страницы: 196

Бренд: MTD Страницы: 16

Бренд: MASSEY FERGUSON Страницы: 31

Бренд: Flymo Страницы: 55

Бренд: Shibaura Страницы: 219

Бренд: Kubota Страницы: 142

Бренд: Harrier Страницы: 34

Бренд: IronCraft Страницы: 44

Бренд: Simplicity Страницы: 16

Бренд: Simplicity Страницы: 22

Бренд: Simplicity Страницы: 32

Бренд: Toro Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды