Jacobsen HR 5111 Скачать руководство пользователя страница 229

Страница: 229 / 339

ELECTRICAL SYSTEM

SECTION 10B. FAILURE ANALYSIS

10B-3

10B

PROBLEM

PROBABLE CAUSE

REMEDY

IMPLEMENT CIRCUITS (Continued)

3. Only one wing does not

a. Arm interlock switch not closing.

a. Check switch/adjust (Section 2C).

come on.

b. Faulty arm interlock switch.

b. Test switch (Section 10G).

c. Faulty motor valve solenoid.

c. Check solenoid plug LED.

ON — Push manual override.

Mower comes on, test solenoid
(Section 10I).

Mower does not come on,
hydraulic problem (Section 8B).

OFF — Check switches and
wiring (Section 10C).

4. Only the front mower

a. Arm interlock switch not closing.

a. Check switch/adjust (Section 2C).

does not come on.

b. Faulty arm interlock switch.

b. Test switch (Section 10G).

c. Faulty motor valve solenoid.

c. Check solenoid plug LED.

ON — Push manual override.

Mower comes on, test solenoid
(Section 10I).

Mower does not come on,
hydraulic problem (Section 8B).

OFF — Check switches and
wiring (Section 10C).

5. Engine shuts down

a. Faulty time delay relay.

a. Test/replace (Section 10H).

immediately when oper-

b. Faulty wiring or bad electrical

b. Test (Section 10C).

ator leaves seat. (Imple-

ground.

ment switch ON.)

6. Engine does not shut

a. Faulty time delay relay.

a. Test/replace (Section 10H).

down when operator

b. Faulty wiring or bad electrical

b. Test (Section 10C).

leaves.

ground.

c. Interlock circuit electrically

c. Reconnect to manufacturer’s

bypassed.

specifications.

GAUGES AND PANEL LIGHTS

1. Engine oil pressure light

a. Bulb burned out.

a. Replace.

does not come on when

b. Faulty sending unit.

b. Replace.

ignition switch is turned
ON.

c. Faulty wiring or bad electrical

c. Test (Section 10C).

Ground BLU wire at

ground.

sending unit; light does

d. 10 amp gauge/panel light circuit

d. Reset/test (Section 10J).

not come ON, see a.

breaker tripped.

Light comes ON, see b.

2. Engine oil pressure light

a. Bulb burned out.

a. Replace.

does not come on when

b. Faulty sending unit.

b. Replace.

ignition switch is turned
ON.

c. Faulty wiring or bad electrical

c. Test (Section 10C).

Ground GRY/WHT wire at

ground.

sending unit; light does

d. 10 amp gauge/panel light circuit

d. Reset/test (Section 10J).

not come ON, see a.

breaker tripped.

Содержание HR 5111




















































































































































































































































































































































Результаты поиска

Содержание HR 5111

Отзывы:

Похожие инструкции для HR 5111

Бренды по названию

Популярные бренды

Jacobsen HR 5111, Инструкции по обслуживанию и ремонту

Результаты поиска

Содержание HR 5111

Отзывы:

Похожие инструкции для HR 5111

Бренды по названию

Популярные бренды