Jacobsen HR 5111 Скачать руководство пользователя страница 15

Страница: 15 / 339

CONTROLS

SECTION 2B. FAILURE ANALYSIS

2B-1

PROBLEM

PROBABLE CAUSE

REMEDY

1. Engine does not turn

a. Parking brake not set.

a. Set parking brake.

over when ignition switch
is engaged.

b. Implement switch ON.

b. Turn OFF.

c. 10 amp shut-off system circuit

c. Reset.

breaker tripped.

d. 50 amp tractor circuit breaker

d. See Section 10B.

tripped.

e. Faulty electrical system.

e. See Section 10B.

2. Engine turns over but

a. Glow plugs not set.

a. Set glow plugs for 7 seconds

will not start.

before starting.

b. 30 amp implement/fuel circuit

b. Reset/test (Section 10J).

breaker tripped.

c. Battery low.

c. Charge or replace (Section 10D).

d. No fuel/obstructed fuel supply.

d. Check fuel level and/or obstruc-

tion. Purge system (Section 3D).

e. Faulty electrical system.

e. See Section 11B.

3. Tractor creeps when

a. Traction linkage centering spring

a. Adjust (Section 2C).

traction pedal is in

not adjusted.

neutral.

b. Binding in the linkage.

b. Repair/lubricate (Sections 2C

and 11B).

4. Parking brake does not

a. Brake not adjusted.

a. Adjust (Section 2C).

hold.

b. Worn brake shoes.

b. Replace (Section 5C).

5. Service brake spongy,

a. Master cylinder fluid level low

a. Check (Section 11).

fades or does not hold.

or no fluid.

b. Air in brake system.

b. Bleed (Section 5E).

c. Worn brake shoes.

c. Replace (Section 5C).

6. Mowers do not lift or

a. Engine rpm too low.

a. Increase engine rpm above

lower properly.

2000.

b. Faulty control valve handle

b. Repair (Section 2C).

linkage.

c. Faulty hydraulic circuit.

c. See Section 8B.

7. Slow traction speed.

a. Engine rpm too low.

a. Increase engine rpm.

b. Traction pedal linkage not

b. Adjust (Section 2C).

adjusted.

c. Traction pedal linkage binding

c. Repair (Section 2C).

or damaged.

d. Parking brake not released.

d. Release.

e. Faulty hydraulic circuit.

e. See Section 8B.

GENERAL

The following table gives common problems, probable
causes, and suggested remedies with page references
to detailed description of remedial procedures.

Содержание HR 5111




















































































































































































































































































































































Результаты поиска

Содержание HR 5111

Отзывы:

Похожие инструкции для HR 5111

Бренды по названию

Популярные бренды

Jacobsen HR 5111, Инструкции по обслуживанию и ремонту

Результаты поиска

Содержание HR 5111

Отзывы:

Похожие инструкции для HR 5111

Бренды по названию

Популярные бренды