manualshive.com logo in svg

Jackson Labs RSR GNSS Transcoder, Руководство пользователя

"Jackson Labs RSR GNSS Transcoder" - передовое устройство для кодирования сигналов GNSS. Для получения подробной информации о настройках и использовании устройства, загрузите бесплатное руководство пользователя на нашем сайте. Легкий доступ к полезной информации для максимальной эффективности работы с устройством.

Поделиться
Скачать
background image

© 2017 Jackson Labs Technologies, Inc.

13

RSR GNSS Transcoder™ User Manual

the RSR GNSS Transcoder™ is about 0.12A at 12V without the CSAC option, and about 0.14A with 
the CSAC option installed.

3.3 Alternate Powering Supply Options

The RSR GNSS Transcoder™ module has the capability to provide power to the external GNSS 
receiver via pin 11 of connector J4. This pin has multiple usage capabilities as listed below:

3.3.1 Powering external GNSS receivers

The RSR GNSS Transcoder™ includes connector J4 with signals designed to interface glue-lessly to 
an external GNSS receiver such as the Rockwell RSR SAASM Puck. It provides power to the 
external GNSS receiver, as well as RS-232 level serial communications and TTL/CMOS level 1PPS 
interfacing from the external GNSS receiver. External GNSS receivers are assumed to be compatible 
to a prime-power input of between 2.7V and 5.5V, with 5V nominal.
When connecting pin 11 of J4 to the prime-power input of the Rockwell RSR Puck or other external 
GNSS receivers, the unit will provide either the supplied USB voltage (2.7V to 5.5V range) to the 
Puck, or it will provide an internally regulated 5.4V supply (whichever is the higher of the two) 
generated from the external 7V to 36V DC prime-power port. The Rockwell Puck or other external 
GNSS receiver can thus be fully powered by connector J4 of the RSR GNSS Transcoder™ module 
and does not require any other wiring connections than those to the transcoder module.

3.3.2 Powering the RSR GNSS Transcoder™ from an external 

LiPo or LiIon single-cell battery

While the primary use of pin 11 of connector J4 is to provide a regulated power to an external GNSS 
receiver, pin 11 of J4 can alternatively be used as a power input to the RSR GNSS Transcoder™ as 
well as the Rockwell RSR Puck or other external GNSS receiver from a single-cell LiPo or LiIon 
battery. Pin 11 will then act as a power-input to the RSR GNSS Transcoder™, and voltages between 
2.7V to 5.5V can be applied, with a typical LiPo battery providing a range of 4.2V (charged) to 3.7V 
(dis-charged). The 4.2V battery power is typically split up and fed to the prime-power input of the 
Rockwell RSR Puck, as well as into pin 11 of connector J4 of the RSR GNSS Transcoder™. 

USB 

power and power to pin 2 of J11 must not be connected when using pin 11 of J4 as the prime 
power input to the RSR GNSS Transcoder™.

Please note that the RSR GNSS Transcoder™ nor the Rockwell RSR Puck 

DO NOT

 disable the 

current draw (do not disconnect the battery) when the LiPo minimum allowable battery voltage of 
3.7V is reached, and continuing to operate the RSR GNSS Transcoder™ from the LiPo or LiIon 
battery below 3.7V cell voltage may damage the battery or cause a battery fire. The user 

must

 

disconnect the battery externally before the terminal cell voltage of 3.7V is reached. External charge 
and control IC’s are readily available that prevent under-voltage conditions on LiPo/LiIon batteries, 
and these should be used when using the system with direct battery power on any of the power input 
connections.

Please note that if power is applied to the USB port or the DC 7V to 36V port that the external 
LiPo/LiIon battery will be charged with up to 5.5V. This can result in battery failure and a 
battery fire, and thus simultaneous operation of a battery connected to J4 pin 11 and any other 
external power source is not allowed.

Содержание RSR GNSS Transcoder

































































































































Отзывы:

Нет отзывов

Похожие инструкции для RSR GNSS Transcoder

3Com CoreBuilder 3500 Installation Manual preview
CoreBuilder 3500
Бренд: 3Com Страницы: 12
Galaxy DX 949 Owner'S Manual preview
DX 949
Бренд: Galaxy Страницы: 12
Galaxy DX 929 Owner'S Manual preview
DX 929
Бренд: Galaxy Страницы: 11
M-system KC Instruction Manual preview
KC
Бренд: M-system Страницы: 3
Yaesu FT5Dr Instruction Manual preview
FT5Dr
Бренд: Yaesu Страницы: 63
Yaesu FT5Dr Operating Manual preview
FT5Dr
Бренд: Yaesu Страницы: 80
YOODA MAGNETIC Deluxe 1Rw Manual preview
MAGNETIC Deluxe 1Rw
Бренд: YOODA Страницы: 2
Camille Bauer SINEAX I 552 Operating Instructions Manual preview
SINEAX I 552
Бренд: Camille Bauer Страницы: 12
Ritron DTXM-460-0BN6I-M-FIPS User Manual preview
DTXM-460-0BN6I-M-FIPS
Бренд: Ritron Страницы: 26
Evikon PluraSens E2608-Cl2 User Manual preview
PluraSens E2608-Cl2
Бренд: Evikon Страницы: 20
Aluprof DC 661 Programming Manual preview
DC 661
Бренд: Aluprof Страницы: 4
GME GX600 Instruction Manual preview
GX600
Бренд: GME Страницы: 12
ENFORCER EB-P104-01Q Installation Manual preview
EB-P104-01Q
Бренд: ENFORCER Страницы: 8
Wouxun KG-UV6X User Manual preview
KG-UV6X
Бренд: Wouxun Страницы: 39
Camille Bauer KINAX 3W2 Operating Instructions preview
KINAX 3W2
Бренд: Camille Bauer Страницы: 5
Evikon PluraSens E2648-NH3-E User Manual preview
PluraSens E2648-NH3-E
Бренд: Evikon Страницы: 21
Harris RF-5000DE Manual preview
RF-5000DE
Бренд: Harris Страницы: 9
RKI Instruments 65-2405RK-05 Operator'S Manual preview
65-2405RK-05
Бренд: RKI Instruments Страницы: 19

Бренды по названию

Популярные бренды

Загрузить еще бренды