English
10
5.4 Commissioning:
Before commissioning, ensure that there are no extraneous objects interfering with the machine’s
moving parts.
Ensure first of all (after verifying electrical compatibility) that the motor is rotating in the right direction,
if so, the head will rise when you pull the control lever towards you. If this is not the case, disconnect
the plug and switch 2 phases in it.
For machine operation, please refer to the “Operation” chapter.
5.5 Danger:
Ensure first of all (after verifying electric compatibility) that the motor is rotating in the right direction.
When the power is switched on, the green button flashes; press to start initialisation. If the head does
not rise during this stage and the indicator flashes quickly, disconnect the plug and switch 2 phases
in it.
Remove the plug from the power socket before any maintenance and/or servicing work.
Any maintenance work or replacement of parts must be carried out by an approved agent.
6 CONTROLS AND SAFETY FEATURES
6.1 Controls:
Your machine is equipped as standard with a mechanical control panel (fig.3).
6.2 Setting area:
The pressure setting and flour recovery area is located at the front of the machine (fig.7), as well as
the pressure time setting area and the half tank/full tank selector.
6.3 Work area:
The work area is at the front of the machine (fig.4).
7 OPERATION
In-tank cutting operating procedure (fig.8, 9)
A. Twist the mushroom (emergency stop) button (fig.3, n°16) ¼ turn to the right if it has not been
released.
B. Press the green button if it flashes to initialise the machine.
C. Open the lid.
D. Choose the position of the head (half tank or full tank) using the selector on the front.
E. Lightly flour the top of the head in the tank using Easyflour.
F. Empty the dough into the tank and spread it around roughly by hand.
G. Lightly flour the top of the dough using Easyflour.
H. You can adjust the tamping pressure using the pressure setting handle located on the front
and the tamping time using the button on the front.
I. With the 10/20 option, you can choose between cutting into 10 or 20 divisions using the
selector on the front.
Содержание Paniform
