J.Sikora Standard MAX Скачать руководство пользователя | Manualshive

Страница: 37 / 44

background image

J.Sikora – Standard MAX Turntable Manual

37

© 2021 Notable Audio Products | www.notableaudio.com

16.2.4.

Slide Arm Tower

In  some  rare  cases,  you  will  need  to
move  the  entire  arm  assembly
(Armboard  and  Arm  Tower).  You  can
adjust this by sliding the Arm Tower in
and and out on the Chassis’ Plinth along
the Arm Tower Track.

Underside of Chassis

The  Arm  Tower  is  mounted  via  a  bolt
and  washer  under  the  Chassis.  Slightly
loosen the Bolt using the largest of the
supplied  Wrenches.  Do  NOT  fully
remove the bolt, only loosen it enough
to  allow  the  Arm  Tower  to  slide  freely
within the Track.

Loosening Arm Tower’s Bolt

You will now be able to slide the entire
Arm Tower along the Track.

Once you move the Arm Tower to the
desired position, re-tighten the Bolt.

Slide Arm Tower Along Track

Arm Tower

Track

Arm Tower

Bolt

«
...
35
36
37
38
39
...
»

Содержание Standard MAX













































Отзывы:

Нет отзывов

Похожие инструкции для Standard MAX

Бренд: Cambridge Audio Страницы: 13

Бренд: Partner Страницы: 2

Бренд: Wacom Страницы: 88

Бренд: Samsung Страницы: 108

Бренд: 7 step Страницы: 27

Бренд: Exagerate Страницы: 32

Бренд: Craig Страницы: 14

Бренд: Craig Страницы: 24

Бренд: Craig Страницы: 26

Бренд: GE Страницы: 99

Бренд: Verizon Страницы: 12

Бренд: Redline Страницы: 42

Бренд: Onyx Страницы: 38

Бренд: boytone Страницы: 14

Бренд: Support Education Страницы: 12

Бренд: SHINOLA Страницы: 20

Бренд: ViewSonic Страницы: 2

Бренд: ViewSonic Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды