background image

10

Manual instruction

EN

•  The  main  voltage  must  correspond  to  the  one 

marked  on  the  technical  data  plate.  Do  not  use 

other sources of power.

•  The  use  of  a  safety  circuit-breaker  is 

recommended  for  the  power  supply  line  for  an 

intervention range of 10 to 30 rated mA. Consult a 

reliable electrician.

•  Before  inserting  the  plug  in  the  mains  socket, 

make  sure  that  the  socket  ratings  are  correct  and 

correspond to those indicated on the rating label on 

the appliance.

CAUTION:  touching  electrified  parts  may  cause 

death by electric shock or burn.

•  Never  move  the  appliance  by  pulling  at  the 

cables.

•  Always guide the connection line safely.

•  Do not use power tools near flammable liquids 

or gases.

•  Always disconnect the appliance from the mains 

supply before transporting it to other places.

CAUTION:  The  appliance  should  always  be 

switched off at the mains before disconnecting any 

plug and socket connector or extension cables. 

•  Do not wire an extension cable directly into your 

device  yourself.  Instead,  take  the  device  to  your 

nearest Performance Power service agent.

•  The  power  supply  cable  should  be  checked 

regularly and before using it , make sure the cable 

is  not  damaged  or  worn  out.  If  the  cable  is  not  in 

good condition, do not use the appliance; take it to 

an authorized service center instead.

Specific safety rules                           

•  Pump may be heavy. If in doubt, take appropriate 

precautions.

•  Motor  must  be  grounded  and  suitable  for  the 

environment in which it is used. Do not use where 

explosion-proof motors are required.

•  Do not allow liquids to come into contact with 

the motor, or any electrical components.

•  Never attempt any service work while the unit is 

still connected to any electrical power source.

•  This pump contains rotating parts. Use caution.

•  When  working  on  or  around  pump,  be  aware 

of  what  liquid  is/has  been  pumped.  If  liquid  is 

potentially harmful, take appropriate precautions.

•  Never  use  any  part  of  the  wiring/electrical 

system  to  lift  or  move  the  equipment.  This  could 

cause a failure of the electrical system, resulting in 

severe shock or death.

•  Do  not  operate  this  pump  or  allow  others  to 

operate it until the instructions and warnings have 

been read and are understood by all involved.

•  Never  work  with  equipment  you  feel  may  be 

unsafe.

•  Pursuant to safety rules the extension cord to be 

used  must  have  a  ground  wire  connected  via  the 

plug to the main circuit ground.

Use of an improper extension cord may 

be  hazardous! The  extension  cord  and 

its connectors must be waterproof and 

approved for outdoor use.

•  If the device’s cable must be replaced, use only a 

power cable provided by the manufacturer.

•  never  handle  the  plug  with  wet  hands.  Keep 

cable connectors dry, and make sure they do not lie 

in the water or on the ground.

•  Use a strain relief device with extension cords to 

relieve tension.

•  To prevent damage of power or extension cords 

should  not  be  driven  over,  squeezed  or  stretched. 

Pro tect the cables against overheating, contact with 

oils or sharp edges.

Suspending the machine on the current-

conducting cable during the operation 

in  wells  and  similar  sites  shall  be 

forbidden.

•  Before using the device check it and its accesso-

ries  for  proper  condition  and  operating  safety.  A 

faulty device must not be used.

•  It is prohibited to pump poisonous, flammable, 

aggressive or explosive substances, or food.

•  Temperature of the liquid being pumped must 

not exceed 40°C.

•  It is prohibited to pump water out of swimming 

pools when people are therein.

•  It  is  prohibited  to  change  the  device’s  internal 

design.

•  Use transport rings for transporting and moving 

the  machine;  car rying  on  cables  or  hoses  shall  be 

forbidden.

Unpacking                                                                                             

When  unpacking,  check  to  make  sure  that  all 

components  are  included.  Refer  to  the  drawings 

on this manual. If any parts are missing or broken, 

please call IVT assistance center.

Содержание MDWP-550

















































































Отзывы: