IV Produkt Envistar Top Series Скачать руководство пользователя страница 54

Страница: 54 / 60

Page 54

Operation and Maintenance Instructions

Envistar Top 04-21

DSET.181201.00.EN

Continuous product development may give rise to specification changes without notice.

Alarm information for inverter and compressor

Alarm Climatix

(code

MX)

Alarm Carel

(code UC, MK,

US)

Explanation and corrective action

Peripherals

AL P02 Compressor Drive:
PERIPHERALS_ERROR

Communication error with the electronic expansion

valve.

Compressor runs at limited speed.

Outside operating range

AL C01 Compressor Drive:
OUT_OF_ENVELOPE

The compressor has worked outside its normal

operating range for a long time and stopped.

Automatic restart occurs after 60 seconds. After

10 repeated restart attempts, the error must be

remedied and the alarm reset.

Overcurrent

AL H01 Compressor Drive:
OVER_CURRENT

A too high current has been registered and the

inverter stopped. The alarm may be caused by e.g.

missing phase (power supply), earth fault, short

circuit, compressor fault or internal fault in the

inverter. The alarm needs to be reset after repeated

start attempts.

High DC voltage

AL H02 Compressor Drive:
DCLINK_VOLTAGE_HIGH

A too high voltage has been registered. The alarm

may be caused by e.g. a power outage. After 10

repeated alarms, the error must be remedied and the

alarm reset.

High inverter temp

AL H03 Compressor Drive:
DRIVE_TEMPERATURE_HIGH

A too high temperature in the inverter has been reg-

istered (>115°C) and the inverter stopped.

The alarm may be caused by e.g. a defective cool-

ing fan, blocked air flow or abnormally high ambient

temperature. The alarm needs to be reset.

Low supply voltage

AL H04 Compressor Drive:
SUPPLY_VOLTAGE_LOW

A too low supply voltage has been registered (<180

V). Check the voltage level. When the voltage

reaches normal level the inverter restarts.

The alarm may be the result of a tripped high

pressure switch (the inverter loses all power).

Reset by pressing the button on the pressure

switch.

High hot gas temp

AL D01 Compressor Drive:
DISCHARGE_TEMP_HIGH

A too high refrigerant temperature has been

registered.

The inverter attempts to restart once normal

temperature has been registered. After 10 restart

attempts, the error must be remedied and the alarm

reset.

Hot gas temp error

AL D03 Compressor Drive:
DISCHARGE_TEMP_INVALID

Hot gas temperature signal is faulty. There is

probably a fault with the wiring or sensor. The

inverter is stopped and restarts when the fault is

fixed.

MB communication er-

ror

AL D04 Compressor Drive:
MODBUS_COM_TIMEOUT

The inverter has lost Modbus communication with

Climatix control equipment and stopped.

Check the high pressure switch by pressing the

button.

When communication is restored, the inverter is

automatically started after 2 minutes.

Содержание Envistar Top Series





























































Результаты поиска

Содержание Envistar Top Series

Отзывы:

Похожие инструкции для Envistar Top Series

Бренды по названию

Популярные бренды

IV Produkt Envistar Top Series, Эксплуатация и обслуживание

Результаты поиска

Содержание Envistar Top Series

Отзывы:

Похожие инструкции для Envistar Top Series

Бренды по названию

Популярные бренды