background image

ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL CODES
IMPORTANT — 

This Document is 

customer property

 and is to remain with this unit. Please return to service informa-

tion pack upon completion of work.

 

HAZARDOUS VOLTAGE - DISCONNECT POWER BEFORE SERVICING

WARNING:

Installer’s Guide

General Information 

1

Unit Installation 

3

Upflow 

3

Downflow 

4

Horizontal Left 

6

Horizontal Right 

7

Duct Connections 

8

Refrigerant Piping 

8

Brazing to Evaporator 

8

Condensate Drain Piping 

9

Electrical — Power Wiring 

10

Control Wiring 

10

Hook-up Diagrams 

11

Outline Drawing 

14

Checkout Procedures 

16

Contents

 A.  GENERAL  INFORMATION

WARNING

!

SAFETY HAZARD 

THIS INFORMATION IS FOR USE BY INDIVIDUALS 

HAVING ADEQUATE BACKGROUNDS OF ELECTRICAL 

AND MECHANI CAL EXPERIENCE. ANY ATTEMPT TO 

REPAIR A CENTRAL AIR CONDITIONING PRODUCT 

MAY RESULT IN PERSONAL INJURY AND/OR PROP-

ERTY DAMAGE. THE MANUFACTURER OR SELLER 

CANNOT BE RESPONSIBLE FOR THE INTERPRETA-

TION OF THIS INFORMATION, NOR CAN IT ASSUME 

ANY LIABILITY IN CONNECTION WITH ITS USE.

CAUTION

!

To prevent shortening its service life, the air handler 

should not be used during the finishing phases of con-

struction. The low return air temperatures can lead to 

the formation of condensate. Condensate in the pres-

ence of chlorides and fluorides from paint, varnish, 

stains, adhesives, cleaning compounds, and cement 

creates a corrosive condition which may cause rapid 

deterioration of the cabinet and internal components.

These instructions do not cover all variations in sys-
tems or provide for every possible contingency. Should 
further information be desired or particular problems 
arise which are not covered sufficiently by this manu-
al, contact your local distributor or the manufacturer 
as listed on the air handler nameplate.
These air handlers are shipped from the factory in the 
upflow or horizontal right configuration and are fully 
convertible to downflow or horizontal left. Refer to Sec-
tion B beginning on page 3 for additional information.

INSPECTION

Check carefully for any shipping damage. This must be 
reported to and claims made against the transporta-
tion company immediately. Check to be sure all major 
components are in the unit. Any missing parts should 
be reported to your supplier at once, and replaced with 
authorized parts only.

CAUTION

!

Cardboard packing material must be removed from in-

side the blower assembly before starting the unit.

Failure to do so may cause indoor blower motor failure.
INSTALLATION LIMITATIONS & RECOMMENDATIONS

The general location of the air handler is normally 
 selected by the architect, contractor and/or home own-
er for the most effective application and satisfaction.

NOTE:  CONDENSATION MAY OCCUR ON THE SUR-

FACE OF THE AIR HANDLER WHEN INSTALLED IN AN 

UNCONDITIONED LOCATION. WHEN UNITS ARE IN-

STALLED IN UNCONDITIONED SPACES, VERIFY THAT 

ALL ELECTRICAL AND REFRIGERANT LINE PENE-

TRATIONS ON THE AIR HANDLER ARE SEALED COM-
PLETELY.

18-GE08D1-10

Convertible Air Handlers

2 – 5 Ton

4TEC3F24B1000A 

4TEC3F36B1000A
4TEC3F42C1000A

Available in French Canadian (FC)

4TEC3F48B1000A

4TEC3F60B1000A 

Содержание 18-GE08D1-10

















Отзывы: