ITW Simco-Ion IQ Power Fantom Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 24

ITW Simco-Ion IQ Power Fantom Скачать руководство пользователя страница 4

2

IQ Power Fantom

5201292 Rev A

CAUTION – Electric Shock Hazard

Electrical installation and repairs must be performed by a skilled electrical

engineer according to the applicable national and local regulations. The

equipment must be properly grounded. Grounding is required to ensure

safe and proper operation and to prevent electrical shocks upon contact.

AVERTISSEMENT– Risque De Choc Électrique

L’installation et le service électrique doivent être effectuées par un électricien

qualifié conformément aux réglementations locales et nationales. Le

matériel doit être correctement mis à la terre. Mise à la terre est nécessaire

pour assurer un fonctionnement sûr et correct et pour éviter les chocs

électriques en cas de contact.

WARNING – Fire Hazard

Keep the unit dry. Do not operate the unit in flammable or explosive

environments.

AVERTISSEMENT – Risque d’incendie

Gardez l’appareil au sec. Ne pas utiliser l’appareil dans des environnements

inflammables ou explosifs.

«
...
2
3
4
5
6
...
»

Содержание Simco-Ion IQ Power Fantom

























Отзывы:

Нет отзывов