manualshive.com logo in svg

ITW Simco-Ion IQ Power Fantom, Инструкция по установке и эксплуатации, Страница: 22 / 24

Поделиться
Скачать
ITW Simco-Ion IQ Power Fantom Скачать руководство пользователя страница 22

20

IQ Power Fantom

5201292 Rev A

PROBLEM 

CAUSE 

SOLUTION 

Fantom not working; 

no indicators, fan not 

running

Power not on

Turn on power switch near line 

cord

Line voltage not supplied

Check line voltage and connections

Blown fuse

Check fuse and replace with 

proper value / type

Warning indicator 

is lit

Unit approaching control limits

Clean ion emitters with the 

built-in point cleaner
Remove the ionizing module and 

thoroughly clean or replace the 

ionizing module

Fault indicator is lit

Unit exceeding control limits

Clean ion emitters with the 

built-in point cleaner
Remove ionizing module and 

thoroughly clean or replace 

ionizing module

Fantom connected to Control 

Station and Fantom AC power 

is off

Apply line voltage to Fantom and 

turn Fantom power switch on

Failure of high voltage power 

supply or control circuitry

Return unit to factory authorized 

repair facility

Communications 

failure

Incorrectly wired cable (check 

against cable illustrations in 

Installation section)

Replace or repair cable

Connector problem

Check connectors for damage and 

proper seating

Содержание Simco-Ion IQ Power Fantom

























Отзывы:

Нет отзывов