ITW Simco-Ion IQ Power Fantom страница 16 Скачать руководство пользователя | Manualshive

Страница: 16 / 24

background image

14

IQ Power Fantom

5201292 Rev A

Paired Sensor

: The specific sensor bar to be used with this ionizing blower for

closed loop feedback control. The default is “none”; a specific sensor bar must be

selected to enable closed loop feedback control. The specific sensor bar is selected by

choosing its “device name”. The sensor bar MUST be located where it will monitor

the material being neutralized.

Balance

: A ratio of input power supplied to the high voltage power supplies that

related to ion balance. In Balanced and CLFB modes this is a display only and non-

editable. The Balance number may only be user adjusted in the Manual modes.

Data Logging

: An on/off setting to enable data logging for this device. The factory

default is off.

Firmware Version

: The firmware revision in the ionizing blower.

«
...
14
15
16
17
18
...
»

Содержание Simco-Ion IQ Power Fantom

























Отзывы:

Нет отзывов

Похожие инструкции для Simco-Ion IQ Power Fantom

Бренд: Panasonic Страницы: 44

Nuclecel P-2063

Бренд: NRD Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды