itema PROMATECH LEONARDO SILVER HI DRIVE 7000 Скачать руководство пользователя

Страница: 29 / 33

Console user manual

01 - 10 - 2004

222

Internal error 12

223

Movement interrupted by coherence sensors (rapiers in shed when shed closed)

231

Coupling not released before engaging

232

Requested staggering not accepted (out of range +/ 30°)

233

Switch loom off and then back on again and then repeat reset procedure

234

PZPT sensor not found before coupling

235

Dobby check sensor not found before coupling; the reason could be a faulty dobby

check sensor. Follow this procedure:

- switch the loom off and then back on again

- bypass the reset procedure (see parag A.6).

- jog the loom a few degrees in slow motion to engage the coupling

- manually synchronise the shafts (see parag. A.8).

- make two complete turns in slow motion: the appropriate alarm will indicate if a

sensor is faulty

- find the fault (sensor, gaps between flags and sensors, wiring, connectors, etc.)

236

More than 4.28° covered without coupling

237

Coupling movement timeout (3.0 sec)

238

Staggering after coupling cannot be established

239

Incorrect staggering after coupling

240

Internal error 240

241

Internal error 241

Содержание PROMATECH LEONARDO SILVER HI DRIVE 7000


































Результаты поиска

Содержание PROMATECH LEONARDO SILVER HI DRIVE 7000

Отзывы:

Похожие инструкции для PROMATECH LEONARDO SILVER HI DRIVE 7000

Бренды по названию

Популярные бренды

itema PROMATECH LEONARDO SILVER HI DRIVE 7000, Руководство пользователя

Результаты поиска

Содержание PROMATECH LEONARDO SILVER HI DRIVE 7000

Отзывы:

Похожие инструкции для PROMATECH LEONARDO SILVER HI DRIVE 7000

Бренды по названию

Популярные бренды