itema PROMATECH LEONARDO SILVER HI DRIVE 7000 Скачать руководство пользователя

Страница: 25 / 33

Console user manual

01 - 10 - 2004

13367

No Driver OK signal from drive: problems with the drive or with the drive/loom

connections.

13368

Enabling relay KD2 open during tracking

13369

Enabling signal not active during tracking

13370

No IGBT repetition signal from drive: problems with the drive or with the drive/loom

connections.

13371

Speed too high when not weaving

13372

RH restart light flashing error

13373

LH restart light flashing error

13374

Loom width not correct, set-up setting error

13375

Loom width not correct, cabling error

13376

Hi Drive device alarm: Drive outputs short-circuited (internal code 1)

13377

Hi Drive device alarm: Motor thermal (internal code 2)

13378

Hi Drive device alarm: motor resolver disconnected (internal code 4)

13379

Hi Drive device alarm: 24 Volt supply error within drive (internal code 8)

13380

Hi Drive device alarm: Overvoltage (internal code 16)

13381

Hi Drive device alarm: Drive dissipator temperature (internal code 32)

13382

Hi Drive device alarm: Motor short-circuited (internal code 64)

13383

Hi Drive device alarm: Drive overvoltage (internal code 128)

13384

Hi Drive device alarm: Error during preloading (internal code 256)

13385

Hi Drive device alarm: Error during braking recovery (internal code 512)

13386

Hi Drive device alarm: Control supply voltage too low (internal code 1024)

13387

Hi Drive device alarm: Speed tracking error (internal code 2048)

13388

Hi Drive device alarm: Undervoltage (internal code 4096)

13389

Hi Drive device alarm: Speed limitation during tracking (internal code 8192)

13390

Hi Drive device alarm: Incorrect E2prom (internal code 16384)

13391

Hi Drive device alarm: Generic alarm

13392

Oil pump motor temperature too high

13393

Drive switched off because handwheel has been used for manual movements;

press slow motion button to reset drive and then wait for the orange lamp to stop

flashing

13394

Main motor temperature probe disconnected

13395

Incoherent status of relays on board JHD (check: JHD, HDI, JHD power supply)

13396

Incoherent enabling status, check JHD and HDI

13397

Incorrect repetition signal for drive IGBT relay; check drive and drive/loom cabling

13398

Wrong oil pump motor temperature: check cabling of NTC probe on oil pump

Содержание PROMATECH LEONARDO SILVER HI DRIVE 7000


































Результаты поиска

Содержание PROMATECH LEONARDO SILVER HI DRIVE 7000

Отзывы:

Похожие инструкции для PROMATECH LEONARDO SILVER HI DRIVE 7000

Бренды по названию

Популярные бренды

itema PROMATECH LEONARDO SILVER HI DRIVE 7000, Руководство пользователя

Результаты поиска

Содержание PROMATECH LEONARDO SILVER HI DRIVE 7000

Отзывы:

Похожие инструкции для PROMATECH LEONARDO SILVER HI DRIVE 7000

Бренды по названию

Популярные бренды