ITech IT7300 Series Скачать руководство пользователя страница 40

Страница: 40 / 73

TRACe Subsystem Commands

Chapter8 TRACe Subsystem Commands

The commands in this subsystem are used to configure and control data

storage into the buffer.

Note:

These TRACe Subsystem Commands are only used for the single-phase

models (IT7321/IT7322/IT7322H/IT7324/IT7324H/IT7326/IT7326H), and the

three-phase models

(IT7322T/IT7322HT/IT7324T/IT7324HT/IT7326T/IT7326HT) do not apply these

commands.

TRACe:CLEar

This action command is used to clear the buffer of readings. If you do not clear

the buffer, a subsequent store will overwrite the old readings. If the subsequent
store is aborted before the buffer becomes full, you could end up with some “old”
readings still in the buffer.

Command syntax

TRACe:CLEar

Parameters

None

TRACe:FREE?

This command is used to read the status of storage memory. After sending this

command and addressing the power supply to talk, two values separated by

commas are sent to the computer. The first value indicates how many bytes of

memory have been stored, and the second value indicates how many bytes of

the memory can be stored.

Query syntax

TRACe:FREE?

Returns

Example

TRAC:FREE?

TRACe:POINts

This command is used to specify the size of the buffer.

Содержание IT7300 Series










































































Результаты поиска

Содержание IT7300 Series

Отзывы:

Похожие инструкции для IT7300 Series

Бренды по названию

Популярные бренды

ITech IT7300 Series, Руководство по программированию

Результаты поиска

Содержание IT7300 Series

Отзывы:

Похожие инструкции для IT7300 Series

Бренды по названию

Популярные бренды