ITech IT7300 Series Скачать руководство пользователя страница 19

Страница: 19 / 73

Remote Control

can set the parity bit in the menu using the front panel

(Shift)

key.

Parity options are stored in a non-volatile memory.

Baudrate

The front panel

(Shift)

(Menu)

button allows the user to set

baud rate which is stored in the non-volatile memory: 4800,9600,19200
38400, 57600,115200

RS-232 connection

Adopt the RS232 cable with DB-9 interface because the serial port of RS232

can be connected with that of the controller (e.g. PC). The modulating cable of

the air-conditioner is not recommended. The pins of plug are shown as the

following table.

If your computer is provided with a RS232 interface with DB-25 plug, a cable

and a adapter with DB-25 plug (one end) and DB-9 plug (the other end) are

required (not the modulating cable of the air-conditioner)

RS-232 plug pins

Pin number

Description

No connection

TXD, transfer data

RXD, receive data

No connection

GND, ground

No connection

CTS, clear transfer

RTS, ready to transfer

No connection

RS-232 Troubleshooting

In case of connection failure of RS232, perform following check:

⚫

Check if the computer and power supply are provided with same

Baud rate, parity check bit, data bit and flow control. The power
supply shall be configured with one start bit (fixed) and one or two
stop bits.

⚫

Just as described in the RS232 connector, appropriate interface

cable or adapter shall be adopted. Notes: even if the cable is
equipped with right plug, internal wiring may be incorrect.

⚫

The interface cable must be connected to the right serial port (COM1

and COM2) of the computer.

Communication Setup

Please ensure the PC and power supply has the same configuration in the

following items.

Содержание IT7300 Series










































































Результаты поиска

Содержание IT7300 Series

Отзывы:

Похожие инструкции для IT7300 Series

Бренды по названию

Популярные бренды

ITech IT7300 Series, Руководство по программированию

Результаты поиска

Содержание IT7300 Series

Отзывы:

Похожие инструкции для IT7300 Series

Бренды по названию

Популярные бренды