ITech IT7300 Series Скачать руководство пользователя страница 24

Страница: 24 / 73

System Commands

mode(control from panel). In this mode ,all of keys on front panel is valid.

Command syntax

SYST:LOC

Parameters

None

Query syntax

None

SYSTem:RWLock

This command is transmit through interface, the same function as

SYST:REM

, but the difference is: this command can lock “LOCAL” button

as well. When this command is executed, the “Local” button can’t switch
to local control mode.

Command syntax

SYST:RWL

SYSTem:BEEPer

This command is used to turn on/turn off the beeper, when the arguments is set

to 1/ON, the beeper is enabled and press keyboard will beeper, otherwise, it is

mute.

Command syntax

SYSTem:BEEPer

Parameters

OFF|ON|0|1

Example

SYST:BEEP 1

SYSTem:COMMunicate:GPIB:RDEVice:ADDRess

This command is used to set the address of GPIB interface.

IT7321 instrument has no GPIB interface, so the command is only applicable to

other models.

Command syntax

SYSTem:COMMunicate:GPIB:RDEVice:ADDRess <NR1>

Содержание IT7300 Series










































































Результаты поиска

Содержание IT7300 Series

Отзывы:

Похожие инструкции для IT7300 Series

Бренды по названию

Популярные бренды

ITech IT7300 Series, Руководство по программированию

Результаты поиска

Содержание IT7300 Series

Отзывы:

Похожие инструкции для IT7300 Series

Бренды по названию

Популярные бренды