ITech IT7300 Series Скачать руководство пользователя страница 43

Страница: 43 / 73

TRACe Subsystem Commands

Example

TRAC:DEL 1

Query syntax

TRACe:DELay? [MINimum | MAXimum | DEFault]

Returns

<NR3>

TRACe:TIMer

This command is used to set the time interval between two adjacent storage

operations, such as the time interval between the second point value and the

third point value.

Command syntax

TRACe:TIMer <NRf>

Parameters

0.00002 to 3600s | MINimum | MAXimum | DEFault

UNIT

S (second)

Example

TRAC:TIM 0.1

Query syntax

TRACe:TIMer? [MINimum | MAXimum | DEFault]

Returns

<NR3>

TRACe:DATA?

This command is used to read the readings stored in the cache and return

these values to the PC interface.

Before sending this command, you must ensure that the cache function is

enabled (i.e.

TRAC:FEED:CONT NEXT

has been executed), and the data

buffer of the IT7300 has data storage. Otherwise, the system will report an error

by directly running the

TRACe:DATA?

command.

Query syntax

TRACe:DATA?

Содержание IT7300 Series










































































Результаты поиска

Содержание IT7300 Series

Отзывы:

Похожие инструкции для IT7300 Series

Бренды по названию

Популярные бренды

ITech IT7300 Series, Руководство по программированию

Результаты поиска

Содержание IT7300 Series

Отзывы:

Похожие инструкции для IT7300 Series

Бренды по названию

Популярные бренды