manualshive.com logo in svg

iSmarGate 01W, Инструкция по эксплуатации, Страница: 25 / 29

Поделиться
Скачать
iSmarGate 01W Скачать руководство пользователя страница 25

INSTALLATION MANUAL · iSmartGate 01W · 

English / REV.3

25

iSmartGate-01W

www.

v2fe

.com

Settings of the iSmartgate-01W in order to get the 

new firmware from the iSmartGateLoader:

1.

 Press both 

CANCEL and OK buttons,

 at the same time, for 10 seconds.

2. 

The text "

UploadFW

" will appear on the display. Press OK to continue.

3. 

The text "

PressWri

" will appear no on the display. Please wait for at least 3 seconds. 

    Then the display screen will turn off and on again.

4. 

At this moment, you are ready to click the "

Write Flash

" button on the iSmartgateLoader software, 

   and the upgrading process will start.

Figure 14. iSmartGateLoader writting flash

Before the firmware’s update, we recommend the user to take note or record the 

GATENAME, 

PASSWORD and PORT

 that appear in the unit’s display. If these settings are wrong, the device 

will be locked for security. Make sure that the device is correctly connected to your network 
by checking the connection between iSmartgate APP and iSmartGate Device.

At this moment, it is really important 

not to switch off neither the iSmartgate-01W nor the network 

cable not the router.

If, for some reason, the upgrading process cannot be completed, your iSmargate-01W will not start, 

or, if it does, the display will remain with no data on it, or completely frozen. 

If that is the case, please push the CANCEL button. Afterwards the unit’s display will turn off and on again. 
Please continue from step 4.

The 

iSmartGate-

01W will load its previous configuration.

ATTENTION

Содержание 01W






























Отзывы:

Нет отзывов