Iron & Oak BHH2013GX Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 50

background image

26

Periodic Maintenance

2. Hydraulic Oil

Change
(continued)

6.

Reinstall suction hose

7.

Dispose of used oil at an oil-recycling center. Used hydraulic oil is hazardous
waste.

8.

Fill the hydraulic tank and replace the oil fill cap.

9.

Disconnect the spark plug wire from the spark plug and turn fuel valve off.

10.

Pull on the starter grip recoil at least 20 times so that hydraulic fluid has cycled
through the pump.

11.

Reconnect the spark plug wire to the spark plug and turn fuel valve on.

12.

Start engine. Extend and retract ram five (5) times to purge air from the system.

13.

Check hydraulic oil level with the engine off and ram retracted. Fill if necessary.
Note: Proper hydraulic oil level is approximately 1” below the top of the tank.

3. Oil Filter

Change

Change return line filter after the first 50 hours of operation, and every 250 hours
thereafter.

1.

Replace return line filter (Refer to the parts breakdown section for part #).

2.

Shut down the engine on the Log Splitter.

3.

Relieve hydraulic system pressure by moving the splitter control lever back and forth several

times.

4.

Unthread the canister and discard it along with the accompanying seal. Note: A strap

wrench may be required. Not provided.

5.

Apply a small amount of lubricant to the new canister seal.

6.

Install the new canister and hand tighten 3/8 to 1/2 turn after gasket makes contact with

head.

4. Spark

Arrestor
Muffler

If the engine is equipped with a spark arrestor muffler, clean and inspect it regularly
(follow engine manufacturer's service instructions).

Replace if damaged.

«
...
24
25
26
27
28
...
»

Содержание BHH2013GX



















































Отзывы:

Нет отзывов

Похожие инструкции для BHH2013GX

Бренд: YARDMAX Страницы: 11

Бренд: Cannon Tools Страницы: 20

Бренд: Yardworks Страницы: 14

Бренд: Champion Страницы: 28

Бренд: Metabo Страницы: 38

Holzspalter 1050

Бренд: Mr.Paldu Страницы: 36

Horizontalspalter 550

Бренд: Mr.Paldu Страницы: 40

Бренд: Gude Страницы: 60

Бренд: Gude Страницы: 57

Бренд: Gude Страницы: 88

Бренд: Gude Страницы: 92

Бренд: Ducar Страницы: 39

Бренд: EarthQuake Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды