Iron & Oak BHH2013GX Скачать руководство пользователя страница 10

Страница: 10 / 50

Moving and Towing to the Job Site

WARNING

The log splitter is heavy. It can crush and cause serious injury if it rolls out of control or
tips over.
Follow the instructions below for safely moving and towing the log splitter.

Moving the log splitter:

1. Engine Off

IMPORTANT: Make sure log splitter engine is off.

Never move the log splitter with its engine running.

2. Fuel Valve Off

(if equipped)

Turn fuel valve off

to prevent carburetor flooding and reduce the chance of fuel

leakage. Refer to Engine owner's manual for fuel valve location.

3. Lock Support

Leg DOWN

Lock support leg in DOWN position

before you move the log splitter.

Move Log

Splitter to
Work Site

Move log splitter by hand either directly to chosen work site or to vehicle hitch
for towing.

(See Step Three: Before Each Use - Work Site Selection and Set-Up)

Important Safety Instructions:



Hills.

Do not move the log splitter up or down hills by hand—use a towing

vehicle.



No riding.

Never allow anyone to sit or ride on the log splitter.



No cargo.

Never transport cargo or wood on the log splitter.

Содержание BHH2013GX



















































Результаты поиска

Содержание BHH2013GX

Отзывы:

Похожие инструкции для BHH2013GX

Бренды по названию

Популярные бренды

Iron & Oak BHH2013GX, Руководство пользователя

Результаты поиска

Содержание BHH2013GX

Отзывы:

Похожие инструкции для BHH2013GX

Бренды по названию

Популярные бренды