Iron & Oak BHH2013GX Скачать руководство пользователя страница 41

Страница: 41 / 50

Assembly Instructions

Step 4 – Coupler to Beam



Link ends of safety chains and lanyard (attached to pin) to safety
quick links.



Tighten locknuts securely with wrench.



Place hitch coupler on tongue and align holes.



Install (1) bolt and (1) locknut in rear hole of hitch coupler.



Position safety chain connectors under hitch coupler.



Insert (1) bolt in front hitch coupler hole while passing through safety
chain connectors.



Thread on (1) locknut and tighten.



Torque to 83 ft.-lbs.

Tools Needed



Ratchet



Torque Wrench



3/4” Socket



3/4” Wrench



Crescent Wrench

Fasteners Needed from Parts Bag:

Coupler to Beam

1/2 Nylon Lock Nut

Qty 2

Coupler to Beam

(through connectors)

1/2 x 3-1/2 Bolt

Qty 2

This view is a
cross section
taken through
the center of
the tongue
and coupler

Содержание BHH2013GX



















































Результаты поиска

Содержание BHH2013GX

Отзывы:

Похожие инструкции для BHH2013GX

Бренды по названию

Популярные бренды

Iron & Oak BHH2013GX, Руководство пользователя

Результаты поиска

Содержание BHH2013GX

Отзывы:

Похожие инструкции для BHH2013GX

Бренды по названию

Популярные бренды