Iron & Oak BHH2013GX Скачать руководство пользователя страница 39

Страница: 39 / 50

Assembly Instructions

WARNING

Make sure beam assembly is standing on flat, level area. Have another person steady the beam to prevent it
from tipping over. The beam assembly weighs approximately 300 pounds and will cause bodily injury if it
falls on someone.

Step 2 – Beam to Tank



Using two (2) people or an appropriate lifting device, remove beam
assembly from shipping pallet.



Carefully position beam assembly on tank assembly and align holes.



Insert (4) bolts, (4) lock washers, and (4) nuts to connect beam to tank.



Torque to 83 ft.-lbs.

Tools Needed



Lifting Device
(optional)



Ratchet



Torque Wrench



3/4” Socket



3/4” Wrench

Fasteners Needed from Parts Bag:

Beam to Tank

1/2 Hex Nut

Qty 4

Beam to Tank

1/2 Split Lock Washer

Qty 4

Beam to Tank

1/2 x 1-1/2 Bolt

Qty 4

Содержание BHH2013GX



















































Результаты поиска

Содержание BHH2013GX

Отзывы:

Похожие инструкции для BHH2013GX

Бренды по названию

Популярные бренды

Iron & Oak BHH2013GX, Руководство пользователя

Результаты поиска

Содержание BHH2013GX

Отзывы:

Похожие инструкции для BHH2013GX

Бренды по названию

Популярные бренды