IPM IP-02S Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 33

background image

13

4.2 Air Motor Assembly Procedure

:

(Reference numbers come from Page 20, Air Motor Section)

Assemble the Air Piston assembly (12). Includes parts (13A through 13G). The Air

Exhaust Valve Plate (13E) and the screws (13A) require the use of Loctite-222 on

the threads to ensure they do not vibrate loose. Tighten the screws to 10-14 inch

pounds.

Note:

Inspect the Air Exhaust Valve Plate to make sure that the gasket is still securely

attached to the center as shown

(far left, in the photo below)

.

1. Assemble the Air Piston assembly (use Loctite-222), with washer (5) onto Piston Rod (11).

Hand-tighten only.

2. Place O-ring (1) inside the groove in the Air Motor Base. Place gasket (6) in the top of the

Air Motor Base, with spring (4) centered inside the gasket resting on the Air Motor Base.

Slide the Piston Rod and Air Valve assembly in to the Air Motor Base (7).

Air Piston assembly (12)

Air Intake

Valve Plate

Spacers, screws

and o-rings

Air Piston

Air Exhaust

Valve Plate

O-ring (1) inserted

in to the groove.

Gasket (6)

«
...
11
12
13
14
15
...
»

Содержание IP-02S


































Отзывы:

Нет отзывов

Похожие инструкции для IP-02S

Бренд: Daikin Страницы: 27

BURKAY 102 Series

Бренд: A.O. Smith Страницы: 24

Бренд: Zehnder Pumpen Страницы: 32

Бренд: SAER Elettropompe Страницы: 76

Бренд: valent Страницы: 20

Бренд: Versamatic Страницы: 18

Бренд: Oase Страницы: 16

Бренд: SAER Elettropompe Страницы: 20

Бренд: Daikin Страницы: 44

Бренд: YAMADA Страницы: 25

Бренд: HAMMELMANN Страницы: 311

Бренд: STIEBEL ELTRON Страницы: 16

Бренд: C.P.A. Страницы: 4

Power Team PE18 Series

Бренд: SPX Страницы: 25

Бренд: OBL Страницы: 36

Бренд: SAMES KREMLIN Страницы: 49

Бренд: Simson Страницы: 16

Бренд: Trane Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды